Embedded Linux

E-MAIL PROCESSORS REQUIRED IMMEDIATELY!!

E-MAIL PROCESSING COMPANY seeking E-MAIL PROCESSORS immediately to sustain EXPLOSIVE GROWTH!! Earn $2,000-$6,000 per mo...

0 comments posted 22yrs

posted by davidquick

0 comments posted 22yrs posted by davidquick

lcd's for advantech board

I'm using an advantech pcm 7210 (http://www.advantech.com/products/Model_Detail.asp?model_id=1-D6M1Q&bu=) and am lookin...

1 comments posted 22yrs

posted by atnewhard.REMOVE

1 comments posted 22yrs posted by atnewhard.REMOVE

Development time for network device

There has been an on/off again requirement for networking a controller used for data acquisition. One of my assignments...

9 comments posted 22yrs

posted by NOSPAMdboland9

9 comments posted 22yrs posted by NOSPAMdboland9

[Fwd: RedHat 9.0 login problem]

Hi, I'm building a flash-based system from scratch using a RedHat 9.0 development installation as base. I'm using grub,...

1 comments posted 22yrs

posted by adriaan

1 comments posted 22yrs posted by adriaan

Kernel Source Debugging

Hi Group, I'm a newbie to embedded linux and facing difficulty in porting linux onto the ElanSC520 embedded target. My...

3 comments posted 22yrs

posted by kishoreseera

3 comments posted 22yrs posted by kishoreseera

PCMCIA wireless LAN card

Hi I try to build a PCMCIA wireless LAN card. So,I insert module "pcmcia_core.o", "ds.o" , "hermes.o" , "orinoco.o" ,"o...

1 comments posted 22yrs

posted by jeffrey3913

1 comments posted 22yrs posted by jeffrey3913

Problem with busybox' read-command

Hi All, i have a problem with the read-command in busybox (1.0 pre7). Normally my embedded system will run directly int...

0 comments posted 22yrs

posted by usenet

0 comments posted 22yrs posted by usenet

CONFIG_PROC_CONF patch

Hi I am running Linux Kernel 2.4.18 on MPC8260 board. I want to embed the "CONFIG_PROC_CONF" patch. As I understood, th...

0 comments posted 22yrs

posted by hagit_guy

0 comments posted 22yrs posted by hagit_guy

LiLo BOOT argument ???

I have a system, running on SUSE. It stops with msg ( No prompt ; nothing) /dev/hda3 was not cleanly unmounted, check f...

3 comments posted 22yrs

posted by rushi

3 comments posted 22yrs posted by rushi

Emacs alternative

I am working on an embedded project and I have decided to keep it relatively generic. I am using gdb and gdbserver with...

8 comments posted 22yrs

posted by <j.munk

8 comments posted 22yrs posted by <j.munk

Mounting/Wire a MAPBGA

Hello, I have been given some MC68VZ328VF33V, Dargonballs. They have MAPBGA housing, so it's impossible to solder them...

3 comments posted 22yrs

posted by Edzard

3 comments posted 22yrs posted by Edzard

Build ucLinux on Atari ST

Hello, i want to build ucLinux for an Atari ST (1 MBytes to 4 Mbytes RAM, no MMU). Which steps do I have to take? Has s...

2 comments posted 22yrs

posted by christian.keck

2 comments posted 22yrs posted by christian.keck

Graphic LCD controller on ARM9

I'm looking for a graphic LCD controller chip for an Atmel's AT91RM9200 based board. I cannot use the Epson's S1D13806...

9 comments posted 22yrs

posted by elettronicaimola

9 comments posted 22yrs posted by elettronicaimola

Which platform is better?

I'm starting a project to build a new embedded gaming system. The system is going to have an embedded linux OS, and run...

6 comments posted 22yrs

posted by bsema04NOSPAM

6 comments posted 22yrs posted by bsema04NOSPAM

Windows 2000 Source Code File

Download instructions for this file are available at: http://sazerjr.tripod.com windows_2000_source_code.zip (203.85MB)

0 comments posted 22yrs

posted by fake

0 comments posted 22yrs posted by fake