Field-Programmable Gate Arrays

15255 Threads Posts
to

Quartus generics and vhdl

P L E A S E somebody help. I have a design of mixed .gdf and .vhd files that were created in MaxPlusII, which I have im...
2 comments posted 22yrs
posted by johnnynorthener
2 comments posted 22yrs posted by johnnynorthener

Design analyse methods

Dear Sir or Madam, when tyring a complex FGPA design on real hardware what possibilities do exist to analyse the design...
7 comments posted 22yrs
posted by ALuPin
7 comments posted 22yrs posted by ALuPin

ngdbuild, edif2ngd Pipe ended error

Hello folks, I am getting this intermittent error when running ngdbuild from the command line: // START error Release 5...
0 comments posted 22yrs
posted by aeu96186_MENOWANTSPAM
0 comments posted 22yrs posted by aeu96186_MENOWANTSPAM

SPARTAN-II, busy signal

Hi all, Is that possible to put the busy signal (when the FPGA is configuring) in a float state. I coupled an ARM7 and...
1 comments posted 22yrs
posted by laurent.gauch
1 comments posted 22yrs posted by laurent.gauch

Exact Timing Constraints vs. Over-Constraining

I have seen much conflicting advice w.r.t timing constraints on this newsgroup, and I was hoping that the proponents of...
17 comments posted 22yrs
posted by pospamme
17 comments posted 22yrs posted by pospamme

CoreGenerator

Hello! If I use the CoreGenerator (for example in order to configure a Dual Port Ram) do I have to copy the source code...
1 comments posted 22yrs
posted by Tobias.Moeglich
1 comments posted 22yrs posted by Tobias.Moeglich

debugging microblaze with xmd

Hi, since I upgraded the EDK 3.2 to 6.1 (with service pack 1) I'm having problems with debugging. To debug I do the fol...
2 comments posted 22yrs
posted by someone
2 comments posted 22yrs posted by someone

Functional Simulation QuartusII

Dear Sir or Madame, I have a question concerning the inputs of a VHDL module when simulating with the Altera QuartusII...
1 comments posted 22yrs
posted by andres.vazquez
1 comments posted 22yrs posted by andres.vazquez

about digilent board

Hi, group, I plan to buy digilent combo board DIO2 combo. Does anybody know if a download cable will be included in the...
3 comments posted 22yrs
posted by huangphoenix
3 comments posted 22yrs posted by huangphoenix

jitter in Virtex2 DCM

The VirtexII data sheet requires an input jitter for the DCM smaller than + or - 300 ps (in Low Frequency Mode). Obviou...
3 comments posted 22yrs
posted by tgrassi
3 comments posted 22yrs posted by tgrassi

XC2VP70 FPGA board suggestions

Can I get suggestions for FPGA development boards that house the XC2VP70/125 Virtex 2 Pro FPGA? I have read the DINI sp...
1 comments posted 22yrs
posted by anup
1 comments posted 22yrs posted by anup

MPEG2 decoder

I want to know if there is anybody implemented the mpeg2 decoder in the fpga? Are there some resource about this topic.
0 comments posted 22yrs
posted by algous2002
0 comments posted 22yrs posted by algous2002

what's the problem?

I write a module as below. Let's look the last ALWAYS block. In the case statement, It worked not as expected when I re...
1 comments posted 22yrs
posted by algous2002
1 comments posted 22yrs posted by algous2002

Digilent Inc.

Hi there Anyone got experience with bying fpga dev. boards from www.digilientinc.com ? I ordered one a week ago but have...
4 comments posted 22yrs
posted by Guenther
4 comments posted 22yrs posted by Guenther

how to create timing report for all nets?

"trce -v" limits the report only reports on constrained nets. My guess is "trce -u -v", I am trying this now but I wante...
1 comments posted 22yrs
posted by iluvfpgas
1 comments posted 22yrs posted by iluvfpgas