Field-Programmable Gate Arrays

15255 Threads Posts
to

Re: Multiple DCM ? (Virtex II)

> Rudi, > > The Architecture Wizard should generate a component with a > CLKIN_IBUFG_OUT output port (if the 100 MHz cl...
2 comments posted 22yrs
posted by russelmann
2 comments posted 22yrs posted by russelmann

REGISTER as a COUNTER in hardware

Hi all, i have a verilog design in which some of the modules are similar to the one given below. it has to shift right...
1 comments posted 22yrs
posted by sand26y
1 comments posted 22yrs posted by sand26y

Re: USB Traffic Generation for FPGA Test

Try checking the testbenches provided with the USB cores in www.opencores.org > Hi, > > the data is itself the USB pack...
0 comments posted 22yrs
posted by engineer_soul
0 comments posted 22yrs posted by engineer_soul

Re: Utility for converting .esf file to .tcl file

> Hi, > I have a esf file with me that contains information about > multi_cycle_paths and false paths. I want to know i...
0 comments posted 22yrs
posted by sdatta
0 comments posted 22yrs posted by sdatta

Msg for Rudolf Usselmann

Hi Rudolf This is with regards to your usb 1.1 function core from opencores.org. Your USB clock needs a 48MHz clock spe...
5 comments posted 22yrs
posted by nospam
5 comments posted 22yrs posted by nospam

Replace PPC in V2P with FPGA fabric!

Hi, I was poking around in FPGA Editor, and I found a switch I hadn't noticed before. There's an Virtex2Pro-specific op...
3 comments posted 22yrs
posted by allan.herriman.hates.spam
3 comments posted 22yrs posted by allan.herriman.hates.spam

Re: Metastablility

> Hi, > > Is it possible to simulate Metastability? Not in the functional > simulation. But in Gate level Netlist simul...
0 comments posted 22yrs
posted by johnjakson
0 comments posted 22yrs posted by johnjakson

does V2p support tristate

Hi, I am trying to create a large bus(32 bits wide), with many slaves recieving and sending data. Should I look for tris...
1 comments posted 22yrs
posted by mer2
1 comments posted 22yrs posted by mer2

Delay on Virtex-II IOB input FF

Hello, I have been simulating a simple 1-bit register using Xilinx XST tools and ModelSim. The VHDL code implements a r...
0 comments posted 22yrs
posted by Sudhir.Singh
0 comments posted 22yrs posted by Sudhir.Singh

Bus interface - read, write signals

Typical bus interface consists of CS, ADDR, DATA, RD and WR signals. The bus transfer type designator may be whether re...
2 comments posted 22yrs
posted by valentin_NOSPAM_NOWORMS
2 comments posted 22yrs posted by valentin_NOSPAM_NOWORMS

licence for Xilinx 2.1i

Hi All, Greetings, I am a student. I found Xilinx 2.1i version software but I think Licence is expired. Can anybody giv...
1 comments posted 22yrs
posted by sona_singh
1 comments posted 22yrs posted by sona_singh

strange error

Hi, i have wrote a VHDL code as below. i use Xilinx foundation platform. The situation is: syntax check
0 comments posted 22yrs
posted by humanbox
0 comments posted 22yrs posted by humanbox

Documentation and manuals for Quatus 3.0...

Being using Quatus 3 for few hours...Compiled a USB phy and a DES without any problem, but where are the manuals for Qu...
1 comments posted 22yrs
posted by kelvin8157
1 comments posted 22yrs posted by kelvin8157

Newbie Question on Xilinx Macros and Pads

Hello, I am using ISE Foundation 5.2i with a Spartan2 and am running into the following problems: 1. I would like to ut...
0 comments posted 22yrs
posted by coasters
0 comments posted 22yrs posted by coasters