Field-Programmable Gate Arrays

15255 Threads Posts
to

ISE

Hi, When i use Synplify to synthesis my VHDL design and then i enter the EDIF result file to ISE 6.1 softare and then i...
0 comments posted 22yrs
posted by benkhalh
0 comments posted 22yrs posted by benkhalh

Compensated clock in Stratix

hi, I want to know what is meant by clock compensation and which clock in the design should be compensated or used as co...
1 comments posted 22yrs
posted by bana8
1 comments posted 22yrs posted by bana8

FPGA/ASIC design comparaison

Hi, I'd like to aske an important, for me, question : I have to compare the improvement of my design (the new version a...
0 comments posted 22yrs
posted by benkhalh
0 comments posted 22yrs posted by benkhalh

[Xilinx 2VP] DDR + Differential Input

Hi guys, It's been ages since I haven't posted anything here... Well, I have a problem trying to build a design: - 311...
5 comments posted 22yrs
posted by ulises
5 comments posted 22yrs posted by ulises

seperate fpga programm and a table in altera

hello! i want to compile a design for a altera acex or cyclon and i want to put additionally a table into it (f.e. a .m...
1 comments posted 22yrs
posted by me
1 comments posted 22yrs posted by me

CfP - Track on EMBEDDED SYSTEMS at ACM SAC 2005

[apologies for cross-postings] ______________________________________________________________________ CALL FOR PAPERS -...
0 comments posted 22yrs
posted by a.bechini
0 comments posted 22yrs posted by a.bechini

NIOS generated code

I think NIOS and SOPC builder are great products. However, there are a couple things I find annoying regarding the gene...
0 comments posted 22yrs
posted by newsmailcomp5
0 comments posted 22yrs posted by newsmailcomp5

Why 18X18 Multipliers in Altera and Xilinx?

Most of the commercial DSP processors today have 16X16 or 32X32 bit signed multilpiers. Why do Altera and Xilinx provid...
3 comments posted 22yrs
posted by deboleena.minz
3 comments posted 22yrs posted by deboleena.minz

crc32 vhdl implementation (4 bit data)

Hy all, I'm currently implementing a receiver (vhdl) part of the ethernet mac which is responsible for the MII interafc...
10 comments posted 22yrs
posted by moti
10 comments posted 22yrs posted by moti

uClinux on MicroBlaze

hi Has anyone used the uClinux port on the Xilinx MicroBlaze? thanks, gesmith __ George Smith Linear Acoustic, Inc
2 comments posted 22yrs
posted by gesmith
2 comments posted 22yrs posted by gesmith

FPGAs starting with incorrect bitstream !?

Hi until recently I did live in good faith that all decent FPGAs do have bitstream integrity checks and do not start in...
13 comments posted 22yrs
posted by antti
13 comments posted 22yrs posted by antti

MAP: what are route-through look up tables

Hi! Could anyone explain, what are route-throughs in look up tables and why are they used? When I run the map command (...
2 comments posted 22yrs
posted by frle
2 comments posted 22yrs posted by frle

Multi-phase Motor Controller?

A new large-diameter, permanent magnet motor line is currently under design for very low speed (2 rad/sec), high-precis...
3 comments posted 22yrs
posted by jjacob
3 comments posted 22yrs posted by jjacob

A simple VHDL question

Could anyone explain what is the meaning of out0 '0'); in the following VHDL code. if reset = '1' then out0 '0'); out1 '...
4 comments posted 22yrs
posted by jaypt
4 comments posted 22yrs posted by jaypt