Field-Programmable Gate Arrays

15255 Threads Posts
to

Re: CAche memory

> I would like to implement Cache memory in to > FPGA / CPLD. I would like to use LRU replacement policy for that. > SO...
1 comments posted 22yrs
posted by johnjakson
1 comments posted 22yrs posted by johnjakson

multiplexing clocks

Hi, I have three clocks connected to input/output pins (not global clock buffers), and then inside the fpga i have a 3...
10 comments posted 22yrs
posted by
10 comments posted 22yrs posted by

Student SATA project

Hi I am a graduate student and would like to implement the SATA I Host Controller Link and Transport layers in an FPGA...
4 comments posted 22yrs
posted by sh_a_12
4 comments posted 22yrs posted by sh_a_12

GLKP and GLKS

What is the difference between GLKP and the GLKS? I am trying to figure out if i have enough global clock resources for...
4 comments posted 22yrs
posted by
4 comments posted 22yrs posted by

Xilinx Spartan3 config problem

Hello all I have designed a board with an XC3S400 and an XCF02S. I can configure both devices through the JTAG interfac...
3 comments posted 22yrs
posted by nicolasmatringe001
3 comments posted 22yrs posted by nicolasmatringe001

low cost MPEG4 codec (from Atmel )

I don't work for Atmel. I am interested in knowing how they did it. (I am using Xilinx at this time - a few very expens...
5 comments posted 22yrs
posted by tony.p.lee
5 comments posted 22yrs posted by tony.p.lee

Unguided slices

Hello I'm trying to perform some partial reconfiguration experiments using EDK/ISE 6.2 on Virtex2 PRO. My design includ...
0 comments posted 22yrs
posted by mlms
0 comments posted 22yrs posted by mlms

Multiple Access on long lines

Hello, I have the problem to discern whether a long line in my VirtexII is used (driven just in this moment). Furthermo...
0 comments posted 22yrs
posted by thomas.reinemann
0 comments posted 22yrs posted by thomas.reinemann

CORDIC NCO Frequency resolution?

Hello everybody!! Maybe some CORDIC guru's can help me??? I've seen a lot of papers, designs and cores and I still don'...
3 comments posted 22yrs
posted by cjmurillo
3 comments posted 22yrs posted by cjmurillo

Actel Fusefile Reverse Engineering

Hi, I am a Actel 54SXA family user. I would like to get from the fusefile what I/O standard I have selected in my Desig...
6 comments posted 22yrs
posted by tatto0_2000
6 comments posted 22yrs posted by tatto0_2000

Routing PLL output

Hi, I have decided to post this problem again because it has gone down in my last post, so here it is; How do I route t...
9 comments posted 22yrs
posted by ALuPin
9 comments posted 22yrs posted by ALuPin

Micromechatronics, is there money in this area?

Hi, there: I was working in ASIC/FPGA industry and I came across a book Miceomechatronics by Kenji Uchino. It reminded...
0 comments posted 22yrs
posted by kelvin_xq
0 comments posted 22yrs posted by kelvin_xq

Problem in Constraining Routing in Xilinx PAR

Hi, I am trying to place and route my design to a specific portion of the FPGA by using the Xilinx modular design flow,...
3 comments posted 22yrs
posted by aman_78in
3 comments posted 22yrs posted by aman_78in

VHDL help needed ($)

I need to accomplish the following using the Spartan-3 Starter Kit. This is a small part of my overall project and I do...
3 comments posted 22yrs
posted by garyswindell
3 comments posted 22yrs posted by garyswindell