Field-Programmable Gate Arrays

15255 Threads Posts
to

Re : fpga +cpu + wireless

Andras, Couldnt a simple RS-232 to USB chip (ex. www.ftdichip.com/FT2232C.htm ) be used instead of the Cypress SL811HS?...
0 comments posted 22yrs
posted by benn686
0 comments posted 22yrs posted by benn686

clock

When configuring a virtex fpga with a prom in master serial mode, how is the clock generated by the fpga. I presume I d...
1 comments posted 22yrs
posted by charlesg77
1 comments posted 22yrs posted by charlesg77

timing constraints and enables

Hello again, CLK = 280MHz A state machine clocked by CLK and enabled by NSI generates a CLKEN signal that enables "othe...
1 comments posted 22yrs
posted by aeu96186_MENOWANTSPAM
1 comments posted 22yrs posted by aeu96186_MENOWANTSPAM

Programmable clock, FPGA PLLs, and Actel PLL Core

Escenario : Need a clock system with range from ~50Mhz to 150Mhz with as much granularity as possible to drive an FPGA....
24 comments posted 22yrs
posted by engineer_soul
24 comments posted 22yrs posted by engineer_soul

Dual 7segment decoder in ABEL

Hi there I'm using the attached module for a dual 7-segment decoder. It works fine except one thing: the segment should...
0 comments posted 22yrs
posted by timoreinhardt
0 comments posted 22yrs posted by timoreinhardt

is this enable structure ok for synthesis/high speed?

Hi Folks, The process below uses two enable signals ANDed together. some_proc: process (CLK) begin if (CLK'event and CL...
2 comments posted 22yrs
posted by aeu96186_MENOWANTSPAM
2 comments posted 22yrs posted by aeu96186_MENOWANTSPAM

ISE 6.1.03i Linux...

Hi all, I have installed ISE 6.1.03i, and I can't get impact to program my development board, using the parallel port.....
1 comments posted 22yrs
posted by f.sethna
1 comments posted 22yrs posted by f.sethna

getting back Xilinx ISE commands

Hi all, I am using Webpack ISE to do PAR for Coolrunner. How to get back all command line from VHDL and UCF parser to J...
7 comments posted 22yrs
posted by laurent.gauch
7 comments posted 22yrs posted by laurent.gauch

Help: Configure PCI Device in Windows 2k

Dear experts in this area, I am trying to configure a PCI board plugged into my PC, running Windows 2000 sp3. This boar...
3 comments posted 22yrs
posted by liat-chuan_kang
3 comments posted 22yrs posted by liat-chuan_kang

How many PCB layers ?

How many layers are normally needed for PCBs using low cost FPGAs ?? I've just been told by a supposed board layout exp...
12 comments posted 22yrs
posted by armcc
12 comments posted 22yrs posted by armcc

regarding opto isolators

Hi all, I was studying some board schematics. In this there are some clocks coming from external world . Before these c...
5 comments posted 22yrs
posted by praveenkn123
5 comments posted 22yrs posted by praveenkn123

Sine Wave Generation

Hi all I need some help with regards to generating a sine wave. I thought abt this problem and some thoughts that came...
8 comments posted 22yrs
posted by nospam
8 comments posted 22yrs posted by nospam

Spartan-3 shipping, or perhaps not!

According to the Xilinx home page two of the Spartan-3 family are in production and shipping. However, when the link is...
9 comments posted 22yrs
posted by aqzf13
9 comments posted 22yrs posted by aqzf13