Field-Programmable Gate Arrays

15255 Threads Posts
to

Configuring Multiple V2Pros with Same Bitstream

Hi, I am trying to configure 8 Virtex 2 Pros (V2P7) (with the same bitstream) on a single board. I will use the the Mas...
3 comments posted 22yrs
posted by Adarsh.Jain
3 comments posted 22yrs posted by Adarsh.Jain

EDK6.1 vs. EDK3.2 issues

Hi there, Anyone having weird memory access and alignment issues with hardware generated using EDK6.2 even automatically...
0 comments posted 22yrs
posted by jonathan
0 comments posted 22yrs posted by jonathan

Spartan-2 Bus Macro, which one also?

Hi, there: I need a bus-macro for spartan-2...It seems the Spartan-2 layout is so much different from Virtex-2, I am su...
0 comments posted 22yrs
posted by kelvin8157
0 comments posted 22yrs posted by kelvin8157

IOB's

Hello I use Xilinx ISE 6.1 for synthesis. I discovered in the floorplanner that there are used very much IOB's. Even mo...
5 comments posted 22yrs
posted by Tobias.Moeglich
5 comments posted 22yrs posted by Tobias.Moeglich

Xilinx Chipscope Sample rate

Hello, I use Xilinx Chipscope for ISE 6.1. My question. What's the sample rate. I couldn't find any documentation about...
6 comments posted 22yrs
posted by Tobias.Moeglich
6 comments posted 22yrs posted by Tobias.Moeglich

Polyphase filter

Working on a polyphase decimator and interpolator. I'm trying to use the same chunk-o-logic to implement both functions...
7 comments posted 22yrs
posted by 0_0_0_0_
7 comments posted 22yrs posted by 0_0_0_0_

using fpga for sampling audio

The planned architecture: telephone line -> ADCs (8k samples pre second)-> FPGA (samples into ram) -> AXIS controller (...
13 comments posted 22yrs
posted by valentin_NOSPAM_NOWORMS
13 comments posted 22yrs posted by valentin_NOSPAM_NOWORMS

Partial Reconfig - PAR fails with ISE 6.1 SP3

I have a simple partial reconfig design. Under ISE6 SP2 it is only routable using fpga editor, command line PAR fails w...
4 comments posted 22yrs
posted by tau14
4 comments posted 22yrs posted by tau14

Plea for help - 29PL141

hi PLD gurus - especially those with grey hair :-) For a fun project, and also on behalf of someone who asked me about...
9 comments posted 22yrs
posted by jonathan.bromley
9 comments posted 22yrs posted by jonathan.bromley

Manual Partitioning to Multiple FPGAs

Hi, I have a design which does not fit on my Altera Stratix device. I need to split it onto 2 Stratix devices. Is it po...
6 comments posted 22yrs
posted by tushitjain
6 comments posted 22yrs posted by tushitjain

Dual-stack (Forth) processors

I want to bring my knowledge about Forth processors up to date, so I'm posting some questions. Who is currently selling...
88 comments posted 22yrs
posted by mygarbagepail
88 comments posted 22yrs posted by mygarbagepail

confused DCM clkin_period vs true input clock

Hi, I am confused at how to set DCM generic parameters on Xilinx FPGA, I know the input clock is 84MHz, and I see my co...
2 comments posted 22yrs
posted by qidanei__2
2 comments posted 22yrs posted by qidanei__2

Xilinx DB-01 info?

I have two Xilinx DB-01 demo boards with the XC2064-33 FPGA, and the ML 4 cable and connector. Does anyone have any inf...
3 comments posted 22yrs
posted by j.s.paNOtrick
3 comments posted 22yrs posted by j.s.paNOtrick

74ls193 in coolrunner

HI All, Was wondering if someone could point me in the right direction on a couple of problems? I am using webpack 4.1...
7 comments posted 22yrs
posted by arcadexpo
7 comments posted 22yrs posted by arcadexpo

Programming an EPC1 conf.Dev. from Altera

Hello, How can i program a configuration Device (EPC1PC8) for my Altera EP1K30 FPGA? It is not in system programmable....
6 comments posted 22yrs
posted by unimatrix9
6 comments posted 22yrs posted by unimatrix9