Various electronic stuff fo those interested

Will pay reasonable shipping costs - but please ask only if you can use a given item set.

1) 6 sets ferrite cores P14/8/I-3C81-A400 (ie: gapped) and retaining clips.

2) Rather old, untested, Analog Devices 310J amplifier module 3L x 1.5W x 0.75H.

3) Misc old but good electrolytic caps, and various digital ICs.

4) Ye Olde "Q" meter: have two and both worked 3-4 years ago. But one does not have the magic unobtanium detector tube and one of the front panel pots (DQ?) went bad so the meters were stripped out for use (any parts or all available). The other is very well packed for shipping, and i will pay the first $50 of shipping.

5) G.E. maggie GL-5J29 no magnet. Good vacuum, presumedly still works. "Classified" stampped on it; made for use in England for the war. Is there any museum that would like to add this to their collection?

6) Promise Ultra 133 TX2 PCI ATA Controller; used once and works fine. No longer need the extra IDE channels. Cost me $43, would appreciate rebate on shipping.

Reply to
Robert Baer
Loading thread data ...

I'd love to have a Q meter again--is this one of the ones with a magic-eye tube?

I'll happily pay shipping and send a nice bottle of wine to console you for parting with it. ;)

Cheers,

Phil Hobbs

Reply to
Phil Hobbs

They are the Boonton 260A Q meter, uses 2 analog meters (one for the DQ). Nice boat anchors at minimum...

Reply to
Robert Baer

analog parts.

first

4b) Incomplete meter has been gutted, due to lack of interest. Available from it is:
  • the meters: "Q" panel meter (0-250) is 100uAFS; the "Multiply Q by" panel meter is 145uAFS;
  • dual variable cap: 14-485pF and 10-245pF, 5"long including shaft, 3.25 wide, 2" high;
  • power transformer and choke;
  • Acme Electric 50VA line regulating transformer (refurbished);
  • other misc parts: potsm fuse holder,momentary on/off/on toggle, etc.
7) Good for power xmitter: variable cap 34-1134F, 6"wide, 4"high, 9" long including shaft. 8) HP310A wave analyzer with manual.

Will pay reasonable shipping costs - but please ask only if you can use a given item set.

Reply to
Robert Baer

analog parts.

first

That's funny, not only did I not know that this group was a for sale group, but I thought it was actually explicitly noted as unacceptable behavior in the group's charter. Not to mention that it has nothing to do with design.

Reply to
Herbert John "Jackie" Gleaso

"Herbert John "Jackie" Gleason" wrote in message news: snipped-for-privacy@4ax.com...

Uhhh...he's giving this stuff away out of the goodness of his heart. Others will then use these for their designs.

But, really, thanks for trying to protect us from ourselves, Jackieass.

Bob

--
== All google group posts are automatically deleted due to spam ==
Reply to
BobW

Just the TURD posting via yet another pseudonym.

Never seen when using NewsProxy ;-)

...Jim Thompson

--
| James E.Thompson, P.E.                           |    mens     |
| Analog Innovations, Inc.                         |     et      |
 Click to see the full signature
Reply to
Jim Thompson

analog parts.

first

"For sale"??? Please tell me *WHERE* i said that?? I am PAYING to send these items to interested person(s)!!

Reply to
Robert Baer

Will pay reasonable shipping costs - but please ask only if you can use a given item set.

1) 6 sets ferrite cores P14/8/I-3C81-A400 (ie: gapped) and retaining clips. 2) Rather old, untested, Analog Devices 310J amplifier module 3L x 1.5W x 0.75H. 3) Misc old but good electrolytic caps, and various digital ICs; aded some analog parts. 4a) Ye Olde "Q" meter; very well packed for shipping, and i will pay the first $50 of shipping. 4b) Incomplete meter has been gutted, due to lack of interest. Available from it is:
  • the meters: "Q" panel meter (0-250) is 100uAFS; the "Multiply Q by" panel meter is 145uAFS;
  • dual variable cap: 14-485pF and 10-245pF, 5"long including shaft, 3.25 wide, 2" high;
  • power transformer and choke;
  • Acme Electric 50VA line regulating transformer (refurbished);
  • other misc parts: pots, fuse holder, momentary on/off/on toggle, etc.
  • Shakesperian FETs: 0A2, 0B2, 6X4, 5763.
5) G.E. maggie GL-5J29 no magnet. Good vacuum, presumedly still works. "Classified" stampped on it; made for use in England for the war. Is there any museum that would like to add this to their collection? 6) *taken* 7) Good for power xmitter: variable cap 34-1134F, 6"wide, 4"high, 9" long including shaft. 8) HP310A wave analyzer with manual. 9) Datak 12-750 Photo etch PCB kit

Will pay reasonable shipping costs - but please ask only if you can use a given item set.

Reply to
Robert Baer

Will pay reasonable shipping costs - but please ask only if you can use a given item set.

1) 6 sets ferrite cores P14/8/I-3C81-A400 (ie: gapped) and retaining clips. 2) Rather old, untested, Analog Devices 310J amplifier module 3L x 1.5W x 0.75H. 3) Misc old but good electrolytic caps, and various digital ICs; aded some analog parts. 4a) Ye Olde "Q" meter; very well packed for shipping, and i will pay the first $50 of shipping. Will strip for parts in about 1 month if no interest. 4b) Incomplete meter has been gutted, due to lack of interest. Available from it is:
  • the meters: "Q" panel meter (0-250) is 100uAFS; the "Multiply Q by" panel meter is 145uAFS;
  • dual variable cap: 14-485pF and 10-245pF, 5"long including shaft, 3.25 wide, 2" high;
  • power transformer and choke;
  • Acme Electric 50VA line regulating transformer (refurbished);
  • other misc parts: pots, fuse holder, momentary on/off/on toggle, etc.
  • Tubes: *taken*
5) G.E. maggie GL-5J29 no magnet. Good vacuum, presumedly still works. "Classified" stampped on it; made for use in England for the war. Is there any museum that would like to add this to their collection? 6) *taken* 7) Good for power xmitter: variable cap 34-1134F, 6"wide, 4"high, 9" long including shaft. 8) HP310A wave analyzer with manual. 9) Datak 12-750 Photo etch PCB kit 10) Tektronix 7A13 Differential Comparitor 11) Tektronix 7D13 Digital Multimeter with LEMO connector for the temperature sensor input (and a schematic for that). 12) 1mm flat cable: 5.75 ft 44 cond DigiKey WM15-5-ND and 5.50 ft 50 cond DigiKey AM50G-5-ND. 13) 10.4" dia X 4" wide coil form suitable for winding an air-core 1H inductor. 14) Wordstar 5.5 with user and 3rd party manuals; working.
Reply to
Robert Baer

Will pay reasonable shipping costs - but please ask only if you can use a given item set.

1) *taken* 2) Rather old, untested, Analog Devices 310J amplifier module 3L x 1.5W x 0.75H. 3) Misc old but good electrolytic caps, and various digital ICs; aded some analog parts. 4a) Ye Olde "Q" meter; very well packed for shipping, and i will pay the first $50 of shipping. Will strip for parts in about 1 month if no interest. 4b) Incomplete meter has been gutted, due to lack of interest. Available from it is:
  • the meters: "Q" panel meter (0-250) is 100uAFS; the "Multiply Q by" panel meter is 145uAFS;
  • dual variable cap: 14-485pF and 10-245pF, 5"long including shaft, 3.25 wide, 2" high;
  • power transformer and choke;
  • Acme Electric 50VA line regulating transformer (refurbished);
  • other misc parts: pots, fuse holder, momentary on/off/on toggle, etc.
  • Tubes: *taken*
5) G.E. maggie GL-5J29 no magnet. Good vacuum, presumedly still works. "Classified" stampped on it; made for use in England for the war. Is there any museum that would like to add this to their collection? 6) *taken* 7) Good for power xmitter: variable cap 34-1134F, 6"wide, 4"high, 9" long including shaft. 8) HP310A wave analyzer with manual. 9) Datak 12-750 Photo etch PCB kit 10) *taken* 11) *taken* 12) 1mm flat cable: 5.75 ft 44 cond DigiKey WM15-5-ND and 5.50 ft 50 cond DigiKey AM50G-5-ND. 13) 10.4" dia X 4" wide coil form suitable for winding an air-core 1H inductor. 14) Wordstar 5.5 with user and 3rd party manuals; working.
Reply to
Robert Baer

Will pay reasonable shipping costs - but please ask only if you can use a given item set.

1) *taken* 2) *taken* 3) *taken* 4a) Ye Olde "Q" meter; very well packed for shipping, and i will pay the first $50 of shipping. 4b) Incomplete meter has been gutted, *taken* 5) G.E. maggie GL-5J29 no magnet. Good vacuum, presumedly still works. "Classified" stampped on it; made for use in England for the war. Is there any museum that would like to add this to their collection? 6) *taken* 7) Good for power xmitter: variable cap 34-1134F, 6"wide, 4"high, 9" long including shaft. 8) HP310A wave analyzer with manual. 9) *taken* 10) *taken* 11) *taken* 12) 1mm flat cable: 5.75 ft 44 cond DigiKey WM15-5-ND and 5.50 ft 50 cond DigiKey AM50G-5-ND. 13) 10.4" dia X 4" wide coil form suitable for winding an air-core 1H inductor. 14) Wordstar 5.5 with user and 3rd party manuals; working.
Reply to
Robert Baer

Is the magnetron like this one?

formatting link

If it is a version that he doesn't have yet, then I'm sure he would give it a good home (but the shipping could be costly, I guess).

formatting link

Chris

Reply to
chrisgj198

It looks very much like that. I pay the shipping; it needs a good home.

Reply to
Robert Baer

I sent him an e-mail. Thanks.

Reply to
Robert Baer

Will pay reasonable shipping costs - but please ask only if you can use a given item set.

4a) Ye Olde Boonton BRC-260A "Q" meter; very well packed for shipping, and i will pay the first $50 of shipping. This will be gutted in about 30 days if there is no interest.

7) Good for power xmitter: variable cap 34-1134F, 6"wide, 4"high, 9" long including shaft.

8) HP310A wave analyzer with manual.

12) 1mm flat cable: 5.75 ft 44 cond DigiKey WM15-5-ND and 5.50 ft 50 cond DigiKey AM50G-5-ND.

13) 10.4" dia X 4" wide coil form suitable for winding an air-core 1H inductor.

14) Wordstar 5.5 with user and 3rd party manuals; working.

Reply to
Robert Baer

Take your SPAM to an appropriate SALES group, IDIOT!

Bad economy brings all the utter idiots out of the woodwork! You are one such idiot. Stop filling the group with your putrifications.

Reply to
Hattori Hanzo

Where are you shipping from? I have a Boonton 260A that has gotten flaky, and might be able to use parts from one to keep the other running.

--
Regards,

John Popelish
Reply to
John Popelish

Does the 310A work? I am getting interested, but i need to know some more about what it does.

Reply to
JosephKK

You are entitled to your rather distorted opinion. READ (if you know how) and notice that I AM PAYING SHIPPING and that I AM NOT ASKING FOR MONEY, so how in the h*ll can it be "sales". It seems that you are the idiot.

Reply to
Robert Baer

ElectronDepot website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.