Microcontroller Discussions

RGB driver with microcontroller.

Hi, I would like to send a RGB LED strip with four potentiometers: 3 potentiometers for the colors red, green, blue. Wi...

3 comments posted 15yrs

posted by jonas .vanhouteghem

3 comments posted 15yrs posted by jonas .vanhouteghem

MAXQ610.

What exactly is a MAXQ610 ? Thanks.

6 comments posted 15yrs

posted by gangprobing.alien

6 comments posted 15yrs posted by gangprobing.alien

MPLAB SIM - Status register...

With C18, I can specify the Status Z register with "STATUSbits.Z" Can I do something similar with MPLAB SIM in the watc...

2 comments posted 16yrs

posted by billnomailnospamx

2 comments posted 16yrs posted by billnomailnospamx

Microchip Forums problems

Is anyone else here from the Microchip Forum? I am user 'Ian.M'. If you haven't visited the Microchip forum recently, t...

3 comments posted 16yrs

posted by ian.m

3 comments posted 16yrs posted by ian.m

A slow year?

Between the PIC and Arduino crowd, you'd think this would be an active group. Is it something someone said? mike -- __...

7 comments posted 16yrs

posted by c

7 comments posted 16yrs posted by c

lowest cost - low pin count flash 8-bit microcontroller

I need to control an RF transmitter IC, through a SPI port. It looks like the PIC12F508/509 is the ~lowest cost 8-bit F...

3 comments posted 16yrs

posted by steve.martindell

3 comments posted 16yrs posted by steve.martindell

Getting started with automation

Hello, I would like to start my first project. My goal is to create a board with an Ethernet interface and and couple d...

2 comments posted 16yrs

posted by fulldecent

2 comments posted 16yrs posted by fulldecent

help with programming please

(this request is a duplication of the newsgroup alt.microcontrollers !!!) Hi, I'm having trouble getting my head around...

1 comments posted 16yrs

posted by andysutton

1 comments posted 16yrs posted by andysutton

Registers , Code Size and LOOPS - AT89S51/2

DJNZ r3,LOOP2 LJMP START Routine_1 CPL P1.0 . . . RET Routine_2 CPL P1.0 . . . RET #################### Thank you - Any...

14 comments posted 16yrs

posted by wicus.maas

14 comments posted 16yrs posted by wicus.maas

DELAY and the 8051

Hi All I've obtained the "The 8051 Micro Controller and Embedded Systems Using Assembly and C-2nd-Ed -", and in this ma...

7 comments posted 16yrs

posted by wicus.maas

7 comments posted 16yrs posted by wicus.maas

Testing all ports on a reset

HI All Is there a quick way to step sequentially through all the I/O Lines of the 4 ports in the AT89???? microcontroll...

5 comments posted 16yrs

posted by wicus.maas

5 comments posted 16yrs posted by wicus.maas

"LOOP" routine in Assembly

DJNZ R2,$ DJNZ R1,REPEAT RET END ################################################# Any suggestions will be greatly appre...

3 comments posted 16yrs

posted by wicus.maas

3 comments posted 16yrs posted by wicus.maas

Developing/compiling software

HI All I've looked at Keil uVIsion (Trial Version) as well as Asem51v1.3 (old stuff). Any suggestions of the compiler s...

38 comments posted 16yrs

posted by wicus.maas

38 comments posted 16yrs posted by wicus.maas

AT89S52 - PLCC vs DIP Package

Hi All Is there any functional/performance benefit from using the 44-Pin PLCC package instead of the 40-Pin DIP package...

16 comments posted 16yrs

posted by abc

16 comments posted 16yrs posted by abc

The best way to learn programming AT89S52

Hi All What is the best way to study programming the AT89S52 ? I'm looking at the below - Atmel 89S52 study Experiment...

2 comments posted 16yrs

posted by abc

2 comments posted 16yrs posted by abc