Field-Programmable Gate Arrays

15255 Threads Posts
to

Can't do a single byte read in Nios?

Hello, I'm having a problem reading a single one byte register on a Nios/Cyclone board. I've seen this on the devkit bo...
5 comments posted 22yrs
posted by kland1
5 comments posted 22yrs posted by kland1

Inserting timing in behavioural simulations

Hi all, I have a problem where my functional simulations are perfect, my timing constraints are all met, my post-par ti...
0 comments posted 22yrs
posted by pl_N0SP4M_apri
0 comments posted 22yrs posted by pl_N0SP4M_apri

Re: The mapper is getting rid of all my logic!!

This typically happens when output signals from a logic block are not connected (though a typo or some other unintended...
6 comments posted 22yrs
posted by jretta
6 comments posted 22yrs posted by jretta

Best price per I/O

I'm looking into a crosspoint switching application where it appears FPGA's are the best choice even though I won't use...
3 comments posted 22yrs
posted by gabor
3 comments posted 22yrs posted by gabor

Re: maybe a stupid question

> > Hi Jean, > > > > I know that the frequency > > synthesis shows is only estimated. > > The real problem is that I ha...
0 comments posted 22yrs
posted by gabor
0 comments posted 22yrs posted by gabor

Re: Bus macro in partial reconfiguration

The bus macro doesn't seem to lack anything, but I discovered that if I route the concerned signal to a "pip" further t...
3 comments posted 22yrs
posted by amaury.anciaux
3 comments posted 22yrs posted by amaury.anciaux

Re: Quartus removes Tristate Buffer

> > The answer is simple: You don't have tristate busses inside (Altera) > > FPGAs. Tristate buffers are substituded by...
5 comments posted 22yrs
posted by already5chosen
5 comments posted 22yrs posted by already5chosen

XC18V master parallel configuration

Hello, I have cascaded two Xilinx PROM's: XC18V04 + XC18V512 in order to configure a XC2VP7 in Master-Parallel mode. Im...
2 comments posted 22yrs
posted by spam*mur
2 comments posted 22yrs posted by spam*mur

Re: simulation time

> Whats a normal execution time for a testbench? There is no such thing as "normal execution time" for a testbench. It...
1 comments posted 22yrs
posted by usenet_10
1 comments posted 22yrs posted by usenet_10

newbie - TCP/IP

Hi Group, I need help on using the XilNet libraray and Xilinx EMAC core. ( www.xilinx.com) I am a newbie to TCP/IP stac...
1 comments posted 22yrs
posted by ramntn
1 comments posted 22yrs posted by ramntn

Re: Virtex 2 PRO Eval/Development platforms

Try at Memec. website : http://www.insight.na.memec.com/cgi-bin/bvutf8/memec/scripts/local/mc_loc_home.jsp?Div=INSIGHT&R...
1 comments posted 22yrs
posted by ramntn
1 comments posted 22yrs posted by ramntn

Re: simalation of gigabit ethernet fails

Modelsim PE (with swift license) or modelsim SE is required to simulate. > Hi, > > I downloaded the 6.1i Update #1 in o...
0 comments posted 22yrs
posted by someone
0 comments posted 22yrs posted by someone

Re: simulation

Meanwhile I received a confirmation about this from xilinx. The gmac core can only simulated with modelsim xe (starter...
0 comments posted 22yrs
posted by someone
0 comments posted 22yrs posted by someone