Latest threads in Electronics Equipmentshow only best voted threads
| Subject | Author | Posted | Replies | |
|---|---|---|---|---|
|
|
WANTED: HAMEG Equipment
I picked up an 8001 Mainframe with two 8028 Spectrum Analyzers in it. I would like to get the 8038 Tracking Generator if anyone has one available. I also need the BNO (BNC Twinaxial) to two BNC Cable...
—
|
8 years ago
|
— | |
|
|
Best RS422/RS485 adapter ?
Hi all. I am seeking advice about rs422/rs485 adapters. I would like to get the "best" USB to serial adapter for diagnostic purpose. I would like something small enough, self powered, allowing...
—
|
8 years ago
|
— | |
|
|
Source for graphic display
Looking for LCD graphic display approximately 6 inches by 1.5 inches (150 mm by 30 mm). High-resolution not required; I'm apparently limited by my size requirements. I don't see anything more than...
11
|
8 years ago
|
11 | |
|
|
Velleman PPS10 RS232 serial cable
Hello i just have got the above handheld oscilloscope,the RS232 cable is missing I was not able to find the schematic on the web, i don't think it is complicated,i'm just in doubt about is it only Tx...
6
|
8 years ago
|
6 | |
|
|
Raspberry Pi sound card problem with multiple electret condenser microphones
I want to process the signals of five electret condenser microphones with raspberry pi and i since the RPI has no audio inputs im thinking of using a sound card. Im looking for a sound card with five...
1
|
8 years ago
|
1 | |
|
|
Re: Securing TE to the bench?
How determined an adversary are you trying to protect against? How much "defacing" of the equipment are YOU willing to undertake?
72
|
8 years ago
|
72 | |
|
|
Fluke 5100B
Hi all, I am looking to calibrate 16 bit A/D converters used in several configurations (DC voltage, AC voltage, and RTD) and was wondering if a Fluke 5100B 4.5 digit calibrator would be a good choice...
2
|
8 years ago
|
2 | |
|
|
KickStarter
Hi All! Just launched a modest KickStarter funding project at the link shown below. Would greatly appreciate if you shared this as you feel appropriate. Also, if you are so inclined, backing of as...
—
|
8 years ago
|
— | |
|
|
Start me off with microcontrollers. Plz.
Hi, I want to get into microcontrollers, just for for and a hobby. I think my first project will be a scrolling display on an 8x8 LED, probably extended to more later. But I wanna do all sorts of...
13
|
8 years ago
|
13 | |
|
|
battery tester -dry cells
Years ago when I worked in the "trade" there was a little black box for testing cells Carbon-Zinc Alkaline etc. Does anyone have an idea of the load resistors used for the various size cells? D, C,...
5
|
8 years ago
|
5 | |
|
|
Dongan 480V 45KVA Three Phase Transformer
Hi! I'm selling an used transformer on ebay.
—
|
8 years ago
|
— | |
|
|
SB Hevi-Duty Electric Transformer 45kva 480V Three Phase For Sale on Ebay
Hi! I'm selling the transformer on ebay.
—
|
8 years ago
|
— | |
|
|
I have released several new videos on YouTube (The Intermidiate Electronics Blog)
Dear members: I have recently released the following videos: Circuit Board contamination: CEA 2006 Rant: Frequency Calibration For Test Equipment: HP/Agilent 44726A Arbitrary Waveform Generator (two...
—
|
8 years ago
|
— | |
|
|
looking for pdf manual for Simpson 276 oscilloscope calibrator
I bought Simpson 276 calibrator, and even though the needle moves when I turn knobs output does not register a single volt. Is there a manual, or instructions on how to operate it properly?
2
|
8 years ago
|
2 | |
|
|
New Youtube video: CEA 2006 Rant (In it I strongly object to using a 14.4 VDC power supply input to test car amps)
Dear members: I have released a new video on YouTube in which I rant about CEA 2006 (Consumer Electronics Association) which specifies a 14.4 VDC power supply for all formal testing. Manufacturers...
—
|
8 years ago
|
— |