Embedded Programming

Bootloader for AVR?

Hello, I'm looking for a Bootloader for the AT-Mega especially 8 and 16. It should be avaiible as GCC-Source and it sho...

1 comments posted 23yrs

posted by daniel

1 comments posted 23yrs posted by daniel

good tutorial for programming AVRs?

Hi - I finally have the capability to write programs to AVRs. It has been quite the challenge to get to this point! So...

4 comments posted 23yrs

posted by nleahcimathotmaildotcom

4 comments posted 23yrs posted by nleahcimathotmaildotcom

PicoServio Controller.

1-Aug-2003 PicoServio Controller. Applications such as industrial control, animatronics, walking pods, mobile robots. h...

0 comments posted 23yrs

posted by z456dy9p_

0 comments posted 23yrs posted by z456dy9p_

PonyProg and PIC16F87xA code protect

I'm having problems with removing the code protect from my PIC16LF874A with PonyProg2000. The erase feature won't remov...

1 comments posted 23yrs

posted by kholmes

1 comments posted 23yrs posted by kholmes

Incorrect AVR UART Frequency

Hi All, I'm trying to set up the UART on a ATMega128L. Problem is the output frequency isn't write. I've got an 8Mhz AV...

4 comments posted 23yrs

posted by ajg112

4 comments posted 23yrs posted by ajg112

Disk on Chip in Std ISA Network Card - Solution

This has been asked a few times before, once by me, and also by others. I installed my DOC in an old WD800 network card...

0 comments posted 23yrs

posted by v.p.crabtree

0 comments posted 23yrs posted by v.p.crabtree

Re: what java enabled devices are there other than cell phones

> Java makes sense for devices that will be getting code via the Internet. It > really doesn't add any advantage (as fa...

6 comments posted 23yrs

posted by hall

6 comments posted 23yrs posted by hall

Re: Linux AVR gcc binary package?

> Hi all, > > Is there a full Linux install for the gcc AVR compiler and programmer? > I'm looking to move off the ever...

8 comments posted 23yrs

posted by bsd

8 comments posted 23yrs posted by bsd

search a low cost PCI card

my company has a project that we want to use a low cost and programmable PCI card to write programs on this card. Does a...

1 comments posted 23yrs

posted by danny.lu

1 comments posted 23yrs posted by danny.lu

Anyone use Infineon 82C900 TwinCAN controller?

Hello, I am trying to comprehend the manual for the Infineon 82C900 TwinCAN controller. I am unable to find any informa...

1 comments posted 23yrs

posted by mgoltsman

1 comments posted 23yrs posted by mgoltsman

Timers in Montavista Linux using Power PC

Hello, I have to design a real time system with a sub 10 ms accuracy using Montavista Linux. There will be an interrupt...

0 comments posted 23yrs

posted by iannou_george

0 comments posted 23yrs posted by iannou_george

BDM Multilink HCS12 connection problem

Hi! I am trying to connect to a >HCS12D64< Processor (16 MHz clock rate)using the >Permicro BDM Multilink 12< from >Cod...

1 comments posted 23yrs

posted by donotreply

1 comments posted 23yrs posted by donotreply

A little Rabbit test for me?

I'm somewhat interested in using the Rabbit 3000 in a product. However, I need to compare performance against an ARM ch...

13 comments posted 23yrs

posted by larwe

13 comments posted 23yrs posted by larwe

Software on Speculation

As a builder builds a house without a buyer, can an embedded software engineer "rationally" develop a former customer's...

4 comments posted 23yrs

posted by RickMerrill

4 comments posted 23yrs posted by RickMerrill

Re: RS232 ports and new PC's

"CM" wrote in news:CSTVa.13267$ snipped-for-privacy@news-binary.blueyonder.co.uk: > I know this has been covered here b...

33 comments posted 23yrs

posted by nospam

33 comments posted 23yrs posted by nospam