Electronic Components

www.arcadechips.com

Hi, I thought I would post a link to my chip site in case I have something you need. www.arcadechips.com Later, Mark Cap...

1 comments posted 19yrs

posted by catfishh

1 comments posted 19yrs posted by catfishh

Ceramic 2.4GHz antenna

I'm in the market for a 2.4GHz ceramic antenna (I've decided on that for a number of reasons). A number of companies do...

37 comments posted 19yrs

posted by peter.smith8380

37 comments posted 19yrs posted by peter.smith8380

TEC and current driver chips for laser?

Hello All, Disclaimer: I don't often work with laser diodes. So please try to restrict the number of "Duh!" statements...

36 comments posted 19yrs

posted by notthisjoergsch

36 comments posted 19yrs posted by notthisjoergsch

look for a RF(2.4GHz or 5.8GHz) -IF (<50MHz) downconverter (Low-IF architecture)

Hi! I have a IF-Tranceiver and I need to RF front end to amplify, downconvert RF signal at 2.4 or 5.8 GHz to IF (no mor...

1 comments posted 19yrs

posted by dayuhuangster

1 comments posted 19yrs posted by dayuhuangster

Looking for a small off the shelf PSU

I've got a little project that I'd like an AC power supply for. I'd like to avoid a wall wart or lump-in-a-cord and I d...

8 comments posted 19yrs

posted by rabbitsfriendsandrelations

8 comments posted 19yrs posted by rabbitsfriendsandrelations

Another Capacitor Value Question

Firstly, thanks to all you GURUS that help us out in this newsgroup from time to time. I have another Cap question for...

13 comments posted 19yrs

posted by tim

13 comments posted 19yrs posted by tim

MY FAVORITE TOOLS

MY FAVORITE TOOLS: BestPair - I wrote this myself and I use it almost every day. Absolutely the very best way to determ...

1 comments posted 19yrs

posted by RespondToGroupPlease

1 comments posted 19yrs posted by RespondToGroupPlease

How to make, where to buy, order 5 kHz, 10 kHz, 15 kHz crystal/ ceramic resonators

Hi, how to make a crystal /ceramic oscilator for a specicfied frequency in kHz range ? Is it posssible to make one on m...

37 comments posted 19yrs

posted by dariusjack2006

37 comments posted 19yrs posted by dariusjack2006

building an electric circuit from paint

I'm an artist/designer and just a tiny bit familiar with electronics and I'm conducting some research for an art projec...

8 comments posted 19yrs

posted by alphacentauri

8 comments posted 19yrs posted by alphacentauri

Ideal Diode like LT4412

Hi, Im looking for a ideal diode circuit. I found a IC from linear, LT4412. This IC has a maximum voltage of 28V, but I...

4 comments posted 19yrs

posted by malte_jahn

4 comments posted 19yrs posted by malte_jahn

Ldo regulators

I'm interested in interfacing to a board that sports a ldo regulator that fix the supply to 3.3V. The regulator is REG1...

13 comments posted 19yrs

posted by electr

13 comments posted 19yrs posted by electr

Today, I had the misfortune

to visit the NXP (nee Philips) website. I am replacing a legacy part and needed the original datasheet for comparison p...

52 comments posted 19yrs

posted by peter.smith8380

52 comments posted 19yrs posted by peter.smith8380

keyed RJ11 jack (DEC style)

I am looking for a keyed RJ11 jack in 6p6c (RJ12). Any type of keying is OK such as DEC MMJ. It must be PC mount side en...

1 comments posted 19yrs

posted by tns1

1 comments posted 19yrs posted by tns1

Looking for an RF power generator

Hi, I am looking for an RF power generator in some 20-100MHz range that would be able to supply some 100W RMS power and...

1 comments posted 19yrs

posted by feeb

1 comments posted 19yrs posted by feeb

200V N-channel FET 200V with nsec speed?

Hello Folks, Is there an n-channel FET that can stomach 180V or more yet switch in nanoseconds? I am looking for around...

28 comments posted 19yrs

posted by notthisjoergsch

28 comments posted 19yrs posted by notthisjoergsch