Spent a while poking around a random display I had lying around, a CVH013HB040BY, and I'm happy to say the pinout is fully mapped out now. I used an ESP32-C3 board to test it and it turned out to be a ST7789V controller, wich was a nice surprise since that's a well supported one. For anyone curious, the pins run like this: 1 is SDA, 2 is SCL, then 3 handles DC, 4 is the reset line, 5 is chip select, 6 goes to ground, 7 is power, 8 and 9 are the backlight cathode and anode, and 10 is another ground. I soldered some thin jumper wires onto an adapter board to reach the ribbon pins, and after a bit of trial and error the screen lit up and started drawing properly. Pretty satisfying result for a part with zero documentation. The whole thing is sitting on my desk glowing right now.
Finally figured out the pinout on a mystery display
Nov 19, 2026
Last reply: 22 hours ago
4 Replies
I went through almost the same thing last year with a panel salvaged from a dead video doorbell, so reading your post felt very familiar. A mystery ribbon, a small board, some very thin wire, and a lot of hoping is exactly how mine went too, except mine took a lot more head scratching before anything showed up on screen. The photo brought it all back. That tangle of fine wires running from the ribbon to the little adapter is precisely what my desk looked like while I was working through it, and that first moment the panel actually draws something instead of sitting dark never gets old. Mine still lives on a shelf now, mounted in a rough frame I cut once I knew it worked.
Landing on an ST7789V is genuinely lucky, since the existing libraries just handle it and you skip the worst part of the job, writing or adapting a driver for something obscure. Mine turned out to be from a different controller family, which is why I ended up hunting through forum threads for pinouts in the first place. One thing I am curious about, how did you keep track of which ribbon position mapped to which function while testing? I kept a handwritten table next to me the whole time and still managed to mix up two of them at one point.
I've got a small pile of salvaged ribbon panels sitting in a drawer and every time I look at them I put them back, so seeing yours actually running makes me want to pull one out tonight. My usual excuse is that guessing the controller wrong risks cooking the panel and I only have one of each, which is why I've stuck to off-the-shelf modules with known pinouts instead. This post is chipping away at that excuse.
What I like is the probe-and-see approach with the ESP32-C3 rather than hunting for a datasheet that probably doesn't exist. Was the backlight wiring the last thing you sorted? I'd have thought the cathode and anode on pins 8 and 9 would be an easy pair to swap, since getting them backwards just leaves everything dark even when the rest of the panel is fine.
Also curious whether the ribbon pins matched the logical order you listed them in, or whether the physical flex came out shuffled compared to how you've written it up. Every mystery panel I've poked at seems to route signals in whatever order suited the original board, not in any order that makes sense to the person reverse engineering it later.
Anyway, enjoy the glow on the desk. Mine can stay in the drawer a little longer, but probably not much longer.
Soldering thin jumpers onto those ribbon pins is the bit that would stop me, my hands just aren't steady enough for joints that small. In your photo the wires coming off the adapter look like a proper spider's nest, and I mean that kindly, that's exactly what this kind of job looks like mid way through. Did you go one pin at a time and check each joint before moving on, or solder the whole row and hope? I'd have bridged two of them for sure.
Update: it's still sitting on my desk running fine. To the person with the drawer full of panels, I say go for it, the guessing game is half the fun. And yeah, the wires on that adapter are a proper mess up close, but steady hands or not, they only need to work once. Would love to see that doorbell panel light up too.
Join the Discussion
Have something to add? Share your thoughts — no account required.
Didn't find your answer?
Ask the community — no account required