Maytag dishwasher suddenly stopped working

SOUNDS LIKE A CRITE CRAWLED UP IN THERE... YOU BETTER CALL IN AN EXPERT TO HANDLE IT. BOOWAHAHAHAHAHA! TGITM

isn't there a removable screen at the bottom that can be renmoved for cleaning if youtake the rotating arm off?

i e g

not that I can see?

(and no loonies staring through screens either)

Anyone come across this problem? no water input but humming and possibly jammed motor?

i e g

My old GE used to have one of thse screens where the impeller is

Hmmm, Water inlet solenoid?

Pump running while dry? Mine has a float sensor on the bottom, left front. If the float sticks up, as it does occasionally, the sensor reports there is standing water and turns on the pump. Dry pump made a grinding/growling noise the entire time.

It might not be relevant, but worth a try to check.

Scott Dunedin

Firstly, the float isnt stuck 'cos when I opened the door, that was the first thing I could see so I THINK I checked it. And with no water coming in, the water input valve was the first thing I thought of, especially as there are a few places on line where this is advised.

My question is whether this is the whole problem and the grinding sound is just a dry pump winding down when it has been started (someone has pressed the start button, causing the hum?) with no water coming in?

Or does some one know whether there are any electric sensors which stop water coming into this unit with (for example) a blown pump or some other major problem? The pump doesnt look like an insuperable problem but I dont know what other technology is built into this unit and Maytag doesnt have any technical support AND I havent made any progress with finding out where the factory is to ask this question

Thanks for the help guys!

Don't write off this suggestion. I had a similar problem with a dishwasher years ago. The 'grinding sound' could be caused by a defective water inlet solenoid. Instead of opening properly, it just buzzed. And don't disregard the possibility of a defective water level switch. The float switch is in series with the fill valve.

Googling 'MDB9601 parts' brings up a wealth of information, including the wiring diagram and assembly drawing of the main pump area. This model has two pumps - the main wash pump which has a food grinder in it's shaft (a possible source of the noise), as well as the drain pump.

PlainBill

. i

he

r g

ng

I hadnt written anything off, in fact I was assuming that it was the water valve and was wondering how i can replace it (even though it is probably just blocked up with dirt from the pipes) in situ. I will have to buy one as the local technicians like to come to any apartment twice, once to diagnose when you tel them to bring a valve because you need a valve and then again to bring the valve.

I had also tried to clean out the impeller mechanism but didnt get very far as the round pump cover under the removable arm seems to be exceptionally difficult to take out.

Whoo!! Lots of stuff. First, I forgot a link to the wiring / assembly drawing

You could simply replace the valve, but I prefer troubleshooting to at least establish that power (and water) is getting to the valve (P/N

6-920534). Prices for this are all over the map - Appliance Depot lists it at $19, others have it as high as $59. They are also available on eBay.

Tearing down the main pump assembly is a pain. The lower rotating arm must be removed, then there are a number of Torx screws that have to be removed. As I recall there are about three layers to it.

PlainBill

dly.

ere i

ng

in

ll

r.

s the

ther

ling

ng

oming

the

r r t

ng

s n

odel_id=3D5170...

Luckily I found one for ten bucks including shipping! I agree, the dissembly of the pump area is a real pain as the mid and upper spray arm seems to prevent the various bits being easily taken off to clean or inspect: Possibly the solution is to use some sort of dishwasher cleaner to get rid of whatever is in the impeller mechanism? On looking at it, it does look filthy but not with anything which would block it. Unlike GE dishwashers, there seem to be various screens to prevent that sort of thing blocking the impeller?.

drawing

The assembly of yours looks similar (if not identical) to mine. I recently had to tear mine down to remove an accumulation of 'crud'. The disassembly goes like this:

1. Remove the lower tray (the upper one also if you desire additional clearance).
2. Remove the plastic nut that holds the lower spray arm in place, remove the lower spray arm.
3. Remove three torx screws (T-15 IIRC) that hold the upper filter plate in place and remove it.
4. Remove the (6?) torx screws that hold the discharge housing in place and remove it (it is a snap fit into the water distribution assembly).
5. Remove the screw holing the impeller in place and remove it.
6. Remove the screws holding the pump filter in place and remove it.
7. Examine the chopper that is just below the screen on the pump filter.

Reassembly is the reverse of disassembly.

I live in an area that has very hard water. Residue had clogged many passages, in addition the screen in the pump filter was partially clogged with food particles.

A common suggestion is to add 1 - 2 cups of white vinegar to the dishwasher to remove any deposits. That did not work well for me.

PlainBill

. i

he

r g

ng

BTW Did you manage to get the valve changed without taking the whole dishwasher out and turning it on its side? (I seem to remember there was a problem installing this dishwasher but I cant remember what it was. I also remember wondering while I was watching it why it wasnt just the five minute install job which it was supposed to be!)

I've never had to replace the fill valve on this dishwasher, but I don't think it's possible to do it without pulling it out. It would require a major contortionist to do it.

PlainBill

loudly.

where i

nding

ght in

fill

ller.

e is the

whether

filling

rking

r coming

th the

s

ater

.

ater

r

ble

nit

n

just

ch.

uding

This

r in

ill

t

x?model_id=3D5170...

rm

The problem I had was with the second part of stage 4. I couldnt get the covers off around the upper spray arms at the rear.

(yes, there is lots of crud in there)

loudly.

where i

in

the

whether

filling

coming

the

drawing

On mine it was not necessary to remove the upper spray arms. The discharge housing slips (snaps) off the tube that leads to the middle and upper spray arms.

PlainBill

Oh that's where I went wrong! It snaps out and I wasn't prepared to apply enough force. Thanks for confirming that, Have now found a valve so cheaply shipped and will take impeller apart to make sure it doesnt need too much attention there as well.

Emphatically didnt want to lose that lower tray-cleaning level which no other dishwasher has now a days!

Oh that's where I went wrong! It snaps out and I wasn't prepared to apply enough force. Thanks for confirming that, Have now found a valve so cheaply shipped and will take impeller apart to make sure it doesnt need too much attention there as well.

Emphatically didnt want to lose that lower tray-cleaning level which no other dishwasher has now a days!

Hey guys, you were right, the humming was a jammed solenoid on the input valve which I changed after finding one for the ten bucks i mentioned. And while the unit may still need cleaning in the impeller mechanism which I couldnt get at, it is now working properly.