Field-Programmable Gate Arrays

15255 Threads Posts
to

latch and shift 15 bits.

Hello all I am trying to implement the following logic in a xilinx XCS05xl FPGA. I have a 15 bit binary counter. I need...
5 comments posted 23yrs
posted by dgleeson-2
5 comments posted 23yrs posted by dgleeson-2

Virtex2Pro--ppc405-FPGA communication

Hi, I have successeuse config the virtex2Pro with a elf file and bit stream file independently. But how to make the pow...
0 comments posted 23yrs
posted by stmak
0 comments posted 23yrs posted by stmak

Smart card ISO 7816 and NIOS Altera

I want to implement a smart card reader on a FPGA Cyclone Altera with NIOS processor inside. Do you know any device dri...
0 comments posted 23yrs
posted by g.giaccaglini
0 comments posted 23yrs posted by g.giaccaglini

ISE : Synthesis process hangs

We are trying to implement a decoder design on a Spartan II(2s200), and when I run the Synthesize process, the message...
1 comments posted 23yrs
posted by
1 comments posted 23yrs posted by

Infer DDR registers from RTL?

Hi all, Does anyone know the right steps to make ISE infer DDR registers from a RTL code? I am following the template t...
1 comments posted 23yrs
posted by anil_khanna
1 comments posted 23yrs posted by anil_khanna

Programmer's unpaid overtime.

Is it fair for programmers to work long hours of overtime and not get paid for the work? If you are a programmer who ha...
8 comments posted 23yrs
posted by kentr0ss
8 comments posted 23yrs posted by kentr0ss

Announcement

I will write a open source arm vhdl model from this month on. I hope to have it ready in approximately 2 months using L...
9 comments posted 23yrs
posted by eiselekd
9 comments posted 23yrs posted by eiselekd

Linux and FPGA compatibility

Hi, I'm a newbie to FPGA and Linux world. I have a general question concerning both. I have a workstation with Linux in...
9 comments posted 23yrs
posted by sleepymish
9 comments posted 23yrs posted by sleepymish

Virtex II DCM & ZBT SRAM

I tried the Xilinx support line Case # 503586 and haven't gotten a good answer so though I would try here. I am trying...
6 comments posted 23yrs
posted by djg
6 comments posted 23yrs posted by djg

Problem in Implementation Costraints

Hello all, While synthesysing the verilog module to generate clock of 12.5MHz from the default clock of XSA100 i.e 50MH...
1 comments posted 23yrs
posted by atif
1 comments posted 23yrs posted by atif

parameter in top module in XILINX ISE 6.1.02

XILINX - ISE 6.1.02 - Modelsim 5.7 SE In verilog I described my top module as follows: module BoothMult (ck, load, ...)...
0 comments posted 23yrs
posted by l.raffo
0 comments posted 23yrs posted by l.raffo

microblaze exceptions

Hi, to install your own exception handler routines for the microblaze, you have to use some library functions. The prot...
0 comments posted 23yrs
posted by someone
0 comments posted 23yrs posted by someone

FPGA Prototyping Board

I've got a design for a $40 assembled and tested fpga dev board that is on a pci card for use in a standard PC (probabl...
7 comments posted 23yrs
posted by thebigbear
7 comments posted 23yrs posted by thebigbear

Xilinx platform flash VCCO/VCCJ

Hi folks, Just want to make sure of something - the VCCO and VCCJ supply voltages for PlatformFlash - I expect these mu...
0 comments posted 23yrs
posted by jwilliams
0 comments posted 23yrs posted by jwilliams