Electronics Repair

21791 Threads Posts
to

Reducing soldering iron heat

I have a 40W soldering iron; I need to solder a small transistor in a PCB. I guessing 40 watts is too much heat for tha...
21 comments posted 20yrs
posted by forkliftcontrols
21 comments posted 20yrs posted by forkliftcontrols

dell monitor problem

hi, i own a dell m993 monitor. after around 6 months of use, the picture is blurred at left top corner. now it is diffi...
1 comments posted 20yrs
posted by manusha
1 comments posted 20yrs posted by manusha

Oscilloscope - 350Mhz - 2 Channels

TEKTRONIX - 485: Portable Oscilloscope. 350 MHz at 5mV/div NSEC/div sweep rate 0 div/NSEC writing speed. Alternate swit...
1 comments posted 20yrs
posted by mr_fixit
1 comments posted 20yrs posted by mr_fixit

CRT for old Tektronix scope, 564B, R564B, TLDM64

Hi, I have a new Tektronix tube part # 154-0737-00. This is a CRT for scopes 564B, R564B, or TLDN64. This is new in the...
6 comments posted 20yrs
posted by tube_s
6 comments posted 20yrs posted by tube_s

Thomson TV 28WS23E error code 27?

Hi, When switching on this TV makes funny noises and then its power led flashes several times the code 2-7. The screen...
0 comments posted 20yrs
posted by personne
0 comments posted 20yrs posted by personne

Sony VO-9850 U-Matic SP tape creasing

Greetings. I have a Sony VO-9850P U-Matic SP vtr that is creasing SP tapes. I took off the top cover and observed durin...
5 comments posted 20yrs
posted by moosh101.286cvz
5 comments posted 20yrs posted by moosh101.286cvz

humming sound from receiver

I bought this Yamaha Receiver R-9 at a garage sale, it sounds great ( way better than my more recent Technics receiver)...
23 comments posted 20yrs
posted by punkinaro
23 comments posted 20yrs posted by punkinaro

Power faults on different Toshiba TVs

I am in the UK and initially purchased a "graded" Toshiba 28" widescreen CRT TV (Model 28ZD28) which after approx 3 mon...
4 comments posted 20yrs
posted by uk_techie_2005
4 comments posted 20yrs posted by uk_techie_2005

Samsung service menu problem

Hello, I'm wondering is someone can help with this issue. I was unfortunately going through the service menu of my Sams...
9 comments posted 20yrs
posted by LeChuck
9 comments posted 20yrs posted by LeChuck

Ibm p202 problems

Hi I have an IBM p202 that has problems at some scan rates it has a pin cousion problem, (sides bowed in) pin cusion co...
2 comments posted 20yrs
posted by c23411778
2 comments posted 20yrs posted by c23411778

Need help repairing TV

I want to try to repair my old TV myself, there is just a few blown parts in the SMPS section. It's a Zenith that doesn...
8 comments posted 20yrs
posted by forkliftcontrols
8 comments posted 20yrs posted by forkliftcontrols

Singing light bulb on dimmer switch

Most light bulbs hum loudly when dimmed via a dimmer switch. A few are ok, because they contain extra filament supports...
8 comments posted 20yrs
posted by daviddiamond.remove-if-not-spam
8 comments posted 20yrs posted by daviddiamond.remove-if-not-spam