Field-Programmable Gate Arrays

15255 Threads Posts
to

Are there more I/O pins than I/O blocks?

I have an XC2S300E-pq08 which the data sheet says has 146 user I/O max. However, the PAR says: Number of bonded IOBs: 1...
4 comments posted 23yrs
posted by kryten_droid
4 comments posted 23yrs posted by kryten_droid

Microblaze & ucLinux for XSV800

I am looking for Microblaze ports in Xess XSV800 (www.xess.com) board platform and a ucLinux (www.uclinux.org) tutorial/...
1 comments posted 23yrs
posted by jmorenoz
1 comments posted 23yrs posted by jmorenoz

Essential hazards in CPLD's?

Hi NG, are essential hazards avoided in CPLD-designs? If for example I were to design a counter with a subsequent compa...
3 comments posted 23yrs
posted by nospam
3 comments posted 23yrs posted by nospam

Minimalist RS232 on Cyclone

Hi, I'm new to this newsgroup, and also a relative FPGA newbie (though have lots of hardware and software experince). I...
4 comments posted 23yrs
posted by andrew.steerATphilips.com
4 comments posted 23yrs posted by andrew.steerATphilips.com

Wishbone interface, FPGA newbie and advice

Hi, I am just starting out with respect to utilising FPGAs within my designs. Up to this point in time I've mostly been...
5 comments posted 23yrs
posted by ckf13
5 comments posted 23yrs posted by ckf13

TNM on Tristate buffers

Hi all, Just wondering if anyone can clarify if TNMs propagate through the tristate control pin of a tristate buffer to...
0 comments posted 23yrs
posted by aperson
0 comments posted 23yrs posted by aperson

ANNC: WebPACK 6.1 tutorials

We have released two tutorials that show how to create FPGA designs using Xilinx WebPACK 6.1: http://www.xess.com/appno...
3 comments posted 23yrs
posted by devb
3 comments posted 23yrs posted by devb

Xilinx XC95108 Chip

I wrote a VHDL program and loaded it into a Xilinx XC95108 chip , unfortunately , the chip's memory is unable to store...
6 comments posted 23yrs
posted by blueforest2
6 comments posted 23yrs posted by blueforest2

comparison of FPGA tools?

I am looking for new tools for FPGA development and wonder if someone has a comparison of different tools available (ev...
0 comments posted 23yrs
posted by m-leik
0 comments posted 23yrs posted by m-leik

TAP controller state vs PROG pin

I know that for Virtex, Virtex-E, and Spartan-II devices, TAP controller is held in reset state when PROG pin is low. T...
1 comments posted 23yrs
posted by rpudlik
1 comments posted 23yrs posted by rpudlik

simulation stops preliminarily

this code causes 100% simulation failure. Rx
2 comments posted 23yrs
posted by valentin
2 comments posted 23yrs posted by valentin

CLKFX problem with a Virtex II

Hi, In the design I am working on there is (for the moment) a DCM generating a CLK0, CLK2X and CLKFX outputs with CLKIN...
1 comments posted 23yrs
posted by jean-francois.hasson
1 comments posted 23yrs posted by jean-francois.hasson

Hit Logic

Hi, I have a question concerning a possibility to find out whether there is a hit or not (cache). How can I check with...
1 comments posted 23yrs
posted by andres.vazquez
1 comments posted 23yrs posted by andres.vazquez