Field-Programmable Gate Arrays

15255 Threads Posts
to

Cheap SRAM?

Hi comp.arch.fpga, I know it's a bit off-topic but because I think that some of you might be able to help me I'll ask a...
3 comments posted 22yrs
posted by studenfn
3 comments posted 22yrs posted by studenfn

frequency multiplication

Hi, for a re-desing i'd like to omit a 'standard' pll with counters etc. used for frequency multiplication, by a cpld....
4 comments posted 22yrs
posted by Jim
4 comments posted 22yrs posted by Jim

Connecting a crystal to a Cyclone or Max PLD

Is it possible to connect a crystal to an Altera Cyclone or a Max pld rather an an external oscillator? And if so, is i...
11 comments posted 22yrs
posted by david
11 comments posted 22yrs posted by david

Nexar for FPGA Design?

Has anyone tried Nexar? (http://www.altium.com/nexar/) Is it any good?
0 comments posted 22yrs
posted by postmaster
0 comments posted 22yrs posted by postmaster

No net attached

Dear sir, I have been troubled by this bug for past couple of hours. When i sythesize my verilog code it says: warning...
1 comments posted 22yrs
posted by sumeet1981
1 comments posted 22yrs posted by sumeet1981

SpyGlass Software

HellO! Can anyone send me Evaluation version of SpyGlass Software. Thank you
1 comments posted 22yrs
posted by ijazag
1 comments posted 22yrs posted by ijazag

programming the mach231

I have a bunch of free mach231 chips but I can't find any information about how to program them. I have gathered from t...
2 comments posted 22yrs
posted by nathan_wilson
2 comments posted 22yrs posted by nathan_wilson

Xilinx ISE 6.2 on Debian

Has anyone succesfully installed the ISE software on a Debian 3.0 system ? I receive errors like: Wind/U Error (294): U...
1 comments posted 22yrs
posted by gvd
1 comments posted 22yrs posted by gvd

Can assign same area group to multiple modules?

May I assign same area_group to multiple modules? e.g. INST "fft_top" AREA_GROUP = "TX"; INST "wtx_top" AREA_GROUP = "TX...
1 comments posted 22yrs
posted by kelvin8157
1 comments posted 22yrs posted by kelvin8157

Ethernet & FPGA

Hi... i'll write my bachelor thesis about the implementation of ethernet and possible tcp/ip layers in an fpga. does so...
2 comments posted 22yrs
posted by bibelwerfer
2 comments posted 22yrs posted by bibelwerfer

Not enough sites to place MULT18X18?

Hi, there: I am implementing a partial chip for virtex-2-6000. My module has 116 multipliers, the module is allocated a...
4 comments posted 22yrs
posted by kelvin8157
4 comments posted 22yrs posted by kelvin8157

Is this a best approach- FPGA ANN

Objective : To build a neural network - lets say a trained ANN in a FPGA Available Resources : Xilinx Virtex-II Pro Hi...
0 comments posted 22yrs
posted by ramntn
0 comments posted 22yrs posted by ramntn

Quartus II Schematic Capture

Hi, Does anybody know how to turn off bounding box display in Quartus II schematic capture (if it's possible at all) ? T...
1 comments posted 22yrs
posted by xxx
1 comments posted 22yrs posted by xxx

turning off clock for parts of design

Hello everyone, I was wondering what the standard design practice is for turning off the clock for some parts of an FPG...
1 comments posted 22yrs
posted by tomtorfs
1 comments posted 22yrs posted by tomtorfs