Embedded Programming

Help with a BootLoader for Motorala Controler

Hello I hope somebody could help me. I know the text is long and I have much questions but maybe there is an answer. I...

2 comments posted 21yrs

posted by steffen.kuehn

2 comments posted 21yrs posted by steffen.kuehn

3-axis 2G MEMS accelerometers - trade for other MEMS/pressure sensors

Hi all, I have been given 21 new sample pieces of Kionix KXM52-L20 3-axis 2G accelerometers. The datasheet for these is...

10 comments posted 21yrs

posted by larwe

10 comments posted 21yrs posted by larwe

Cool...GPLed EDA run on windows and linux

This is so cool..Finally, there's real EDA on linux.. Check this out : http://www.lis.inpg.fr/realise_au_lis/kicad/ It...

1 comments posted 21yrs

posted by kunilkuda

1 comments posted 21yrs posted by kunilkuda

interfacing CCD with LCD

i need to interface a ccd with an lcd. i am trying to make a viewfinder. does anyone know what type of lcd controller s...

0 comments posted 21yrs

posted by 202511233

0 comments posted 21yrs posted by 202511233

PAL

Can anyone tell me which software was used to compile following code into burnable PAL 16L8 image? [===code===] #includ...

6 comments posted 21yrs

posted by cr0acker

6 comments posted 21yrs posted by cr0acker

looking for open source

Hi All, I am looking for an embedded open source group to join in. I have 15 years experience on embedded software deve...

5 comments posted 21yrs

posted by jianglica

5 comments posted 21yrs posted by jianglica

Flash write issue

Hi all guys, I am requested to add some time-clock information in flash, to indicate how long the device is used by end...

11 comments posted 21yrs

posted by sailor.gu

11 comments posted 21yrs posted by sailor.gu

Debugging by bsing SW interrupts instead of HW interrupts

My problem is to test my driver software ,but the asic chip is not ready yet.I can simulate the registers of the asic e...

4 comments posted 21yrs

posted by istakoz2000

4 comments posted 21yrs posted by istakoz2000

arm920T: (serious) Interrupt latency problem

Hi, I am developing evaluation board using samsung s3c2410 (Arm920T core chip. It is connected DSP which sends interrup...

5 comments posted 21yrs

posted by dungglee

5 comments posted 21yrs posted by dungglee

LCD module integration

Hi, I'm trying to build a display board with 320x240 dots RGB (6-bits each LCD module. Any recommendations for a partic...

2 comments posted 21yrs

posted by karun_sriram

2 comments posted 21yrs posted by karun_sriram

PCI conformance requirement ?

I'm looking into using a particular PCI peripheral card as OEM equipment in a commercial system. PCI interface is based...

1 comments posted 21yrs

posted by rrr

1 comments posted 21yrs posted by rrr

PCMCIA CardBus connect to microcontroller ?

I'm looking for useful information how to connect PCMCIA CardBus to micrcontroller i.e. Atmega128. Is it necessary to u...

1 comments posted 21yrs

posted by anokNOSPAM

1 comments posted 21yrs posted by anokNOSPAM

Hexadecimal display on terminal program

I am stuck with a W2000 desktop as a test driver. Is there any way to configure Hyperterminal to display received data...

4 comments posted 21yrs

posted by rphenry

4 comments posted 21yrs posted by rphenry

Serial/Ethernet Converter

Hi everyone! My requirement is very simple. I have serial port access on my product but I want ot interface it with PC...

8 comments posted 21yrs

posted by shoaib.ali

8 comments posted 21yrs posted by shoaib.ali

CF card interfacing problems

Hi all, My board has a CF-slot which conforms to the CF/CF+ 2.0 specifications.I am trying to interface a SanDisk or Le...

1 comments posted 21yrs

posted by abhilashkv

1 comments posted 21yrs posted by abhilashkv