Embedded Programming

AVR Silly Interrupt problem

I have timer0 set to overflow and generate an interrupt, but for whatever reason AVR Studio doesnt seem to be doing wha...

17 comments posted 20yrs

posted by jasimpson

17 comments posted 20yrs posted by jasimpson

books or materials for vxworks

i have recently joined a course in embedded system design. can any one suggest me some good books for vxworks along with...

1 comments posted 20yrs

posted by msc.sudheer

1 comments posted 20yrs posted by msc.sudheer

Source for custom membrane switch / enclosure / artwork?

Hello, Can anyone recommend a manufacturer for a small (hopefully large someday) run of custom membrane switches (6 but...

0 comments posted 20yrs

posted by johnharlow

0 comments posted 20yrs posted by johnharlow

Using a 4mhz clock with AVR problems

Just getting to know embedded programming with the atmega8. I've had some experience using the PIC chip with MicroCode...

2 comments posted 20yrs

posted by david.nolen

2 comments posted 20yrs posted by david.nolen

AVR32 - anyone using it?

32 bit AVR to compete with the ARM... Atmel AVR32. Anyone using it? http://www.embedded.com/showArticle.jhtml?articleID...

5 comments posted 20yrs

posted by mw

5 comments posted 20yrs posted by mw

Looking for ARMARCH5/6 Eval board that supports big and little endian.

As it says, looking for a reasonably priced eval board(s) that support ARM v5 and/or v6 CPUs big and little endian. Pref...

0 comments posted 20yrs

posted by spammers_lie

0 comments posted 20yrs posted by spammers_lie

MC9S08GT or GB standalone programming.

We have quite a few products which use the MC68HC705C8 micro from Freescale. We are deciding to move to the MC9S08 to k...

1 comments posted 20yrs

posted by novatech

1 comments posted 20yrs posted by novatech

Minimum Pin Count For CompactFlash access

This is closely tied to my other thread about using Compact Flash in True IDE mode. The main goal is minimum pincount....

2 comments posted 20yrs

posted by nospam

2 comments posted 20yrs posted by nospam

DS1307 no response

Respected Sir /Madam I am developing a project for which i have to interface the ds1307 rtc to it. The controller used...

12 comments posted 20yrs

posted by nava555

12 comments posted 20yrs posted by nava555

improper functioning (ds1307)

Respected Sir I am developing a module regarding to medical electronics to which i have to interface the ds1307 rtc chi...

1 comments posted 20yrs

posted by nava555

1 comments posted 20yrs posted by nava555

Optrex F-51852 LCD initialization

Hi , LCD is connected to Renesas M30626 as extended memory, unfortunately i can't get it to display anything. Connectio...

1 comments posted 20yrs

posted by raivo.leini

1 comments posted 20yrs posted by raivo.leini

Re: want to learn embedded linux

> > well, i am working on the microcontroller ARM but i am using it as a > simple > microcontroller and want to use RTO...

1 comments posted 20yrs

posted by nospam

1 comments posted 20yrs posted by nospam

Opinion on SofTec Microsystems Products?

Hi, We've been using products from P&E Micro (www.pemicro.com). Recently, we've received sales literature from SofTec M...

0 comments posted 20yrs

posted by dta

0 comments posted 20yrs posted by dta

Embedded Linux / Hardware Wiz

We're seeking a consultant with significant development experience configuring/modifying/developing for linux distribut...

1 comments posted 20yrs

posted by ecomm

1 comments posted 20yrs posted by ecomm

PSOC POWER OPTIMIZATION

HI THIS IS PRAVEEN , I JUST WANT TO KNOW THAT ANY TECHNIQUE TO OPTIMIZE THE POWER OF AN PSOC CY8C27443 SERIES MICRO CONT...

4 comments posted 20yrs

posted by kpraveen008

4 comments posted 20yrs posted by kpraveen008