Embedded Programming

lottery terminal architecture

Shalom, I have seen many lottery terminals around me. I also know the transaction supported by the terminals, but was w...

0 comments posted 23yrs

posted by speckle_noise

0 comments posted 23yrs posted by speckle_noise

Need Sample MPC860 Code

Hi, i am working with an Embedded Planet RPX MPC860 board and am totally new to embedded programming. All i want to do...

7 comments posted 23yrs

posted by fahd_abidi

7 comments posted 23yrs posted by fahd_abidi

Re: Ruggedizing PC104?

I would like to thank everyone for their input. We are using the Tri-M Systems Can-Tainer with the Versa-Tainer shock m...

0 comments posted 23yrs

posted by wifiwardriver

0 comments posted 23yrs posted by wifiwardriver

Re: SLIP on win2k

"Ralph Mason" wrote in message news:... > > Hi > > > > I've been porting a TCP/IP stack (UIP) to run on atmel avr proce...

0 comments posted 23yrs

posted by earth

0 comments posted 23yrs posted by earth

Q: cheap case for Advantech boards?

Hi, I've got several different Advantech 3.5" biscuit SBC's that I'm playing around with. Since I'm only a hobbyist, I...

3 comments posted 23yrs

posted by jonathanNOFISH

3 comments posted 23yrs posted by jonathanNOFISH

Embedded system with RF

Hi all- I am new to embedded systems area. I have a question. I want an embedded system with the following specs. a) It...

2 comments posted 23yrs

posted by suresh1

2 comments posted 23yrs posted by suresh1

Re: Embedded Ethernet

"Craig Rodgers" wrote in news:bdcak4$fc$ snipped-for-privacy@spacebar.ucc.usyd.edu.au: > I'm trying to provide network...

29 comments posted 23yrs

posted by nospam

29 comments posted 23yrs posted by nospam

5380 SCSI controller

Does anyone know if the 5380 SCSI controller is still available anywhere in 40 pin DIP? Someone just ordered some board...

1 comments posted 23yrs

posted by sfp

1 comments posted 23yrs posted by sfp

Re: Rapid MCU development

Thanks for your moral support, really appreciate it man! > Haris wrote: > > > > Hello everyone... > > All of your respo...

0 comments posted 23yrs

posted by haris

0 comments posted 23yrs posted by haris

Embedding 802.11b

I'm trying to figure out how to at 802.11b connectivity to an existing product. From doing a Google search, it seems li...

3 comments posted 23yrs

posted by embeddedmatt

3 comments posted 23yrs posted by embeddedmatt

PCI rev.2.1 needed

Hello, I need PCI rev.2.1 specification. Does anyboday know where can i get it? Can anyone send me a copy ? Thanks. Sara...

4 comments posted 23yrs

posted by sarahshenca

4 comments posted 23yrs posted by sarahshenca

TCP stack for ARM Emulator 7T

eCos supports TCP and the ARM line of processors and we have found a TCP stack for the Integrator 7T SBC. But we have n...

0 comments posted 23yrs

posted by rhyphenlarkin

0 comments posted 23yrs posted by rhyphenlarkin

Sending GSM SMS

I am faced with a billing situation in an industrial application that only sends an SMS message when an alarm condition...

5 comments posted 23yrs

posted by getsmedonospamwn

5 comments posted 23yrs posted by getsmedonospamwn

Arbor EmCORE-i413 refresh rate

Hi all... I'm using Arbor EmCORE-i413 with an application that runs under MS-DOS in 640*480 16 colours. In this conditi...

0 comments posted 23yrs

posted by udicomNOSPAM

0 comments posted 23yrs posted by udicomNOSPAM

Re: Choosing the right RF module?

lynx has a 433Mhz .Tx / RX pair chips .Using Amplituse shift keying .Simply modules a binary code on a 433 mhz carrier....

2 comments posted 23yrs

posted by hsuri

2 comments posted 23yrs posted by hsuri