Latest threads in Embedded Programmingshow only best voted threads
Subject | Author | Posted | Replies | |
---|---|---|---|---|
|
NGW100 - store root and /usr images for later restore
I was recently given an Atmel NGW100 board (AVR32) and have been learning about it. I have gotten to the point where I can load root and /usr images to the board and run them. What I need to do now is...
1
|
15 years ago
|
1 | |
|
looking for low cost SBC with small touchscreen, RS232, USB and some I/O's
I have to build a system with a small Display (e.g. 5") with touchscreen, some digital I/O's, 1 ADC 8bit, 2xRS232, 1xUSB, RTC. -> would a PC/104 system be good for that, or are there any other better...
7
|
15 years ago
|
7 | |
|
Sensirion RH sensor Temp Compensation using an 8 bit PIC
I'm trying to implement temperature compensation on a Sensirion SHT11 RH sensor. I've got most of it up & going using a 16F628 + *assembler* but I am having a hard time wtih the temp compensation - in...
24
|
15 years ago
|
24 | |
|
Need Lattice FUSE TABLE --->> LOGIC conversion service. $$$
Hello, Have Lattice MACH221 fuse table. Need logic schemetic or at a minimum a boolean equation. Can anyone provide this service? Regards, RJ Silva
1
|
15 years ago
|
1 | |
|
using winavr
Hi all I am into using CAN FESTIVAL stack over ATMEGA64. The stack is a gcc code and I am new to gcc. I chose to work on WinAVR on windows. I made a sample makefile using Mfile tool for testing. My...
1
|
15 years ago
|
1 | |
|
Bothhandusa RJ-45 connector
I am looking for a replacement for the Bothhandusa RJ-45 connector. I have been unsuccessful in locating soldertail plating information for my company's Pb-free screen. Any help would be appreciated!...
—
|
15 years ago
|
— | |
|
It was not intentional to post it twice!!!
I'm sorry paul but I had posted this question from in this group but it said it needed to moderate my question and I waited for two days but my question did not come up here. So I posted the question...
8
|
15 years ago
|
8 | |
|
Which ARM-7 with 4 32-bit counter, 4 pulse generator & USB
Hi friends, I am working on CNC controller project which requires, 4 pulse generator, 4 32-bit counter, and USB 2.0 slave (Full speed) Thanks
1
|
15 years ago
|
1 | |
|
Microprocessors for Java or MPEG4
Hello I'm looking for two microprocessors, one that optimized for Java applications and another that has a compressor MPEG4. I need to do two designs, one with uClinux running an application in Java...
4
|
15 years ago
|
4 | |
|
Create device ram in uClinux
Hello I have a little doubt with the design of a system with uClinux, the design consists of a Samsung S3C2440, 64MB of flash memory and 64MB of RAM. I need to create a unit in memory of 128MB, this...
—
|
15 years ago
|
— | |
|
AT91SAM9261-EK
I have a new AT91SAM9261-EK development board that I would like to sell. It is listed on ebay if anyone is interested. -Rob
—
|
15 years ago
|
— | |
|
conversion of voice to frequency domain using fft
Hai to all, Iam new to this forum and dsp. Iam involved in converting a 5sec voice to frequency using a fft. Using pic24f series i need to accomplish this. Can anyone guide through this process? What...
5
|
15 years ago
|
5 | |
|
Automatic Pill Dispenser
Hi, I am new the website but I've taken a microprocessor class before and used the HC12 board so I know the basics of embedded design. For my senior project we are suppose to design a pill dispenser...
9
|
15 years ago
|
9 | |
|
slave mode operation of c3038 digital camere
hello, i am working on spartan III 1800a dsp fpga development board,what i am trying to do is interfacing the c3038 digital camera(which uses ov6630 cmos image sensor)in slave mode but the timing...
—
|
15 years ago
|
— | |
|
kgdb8250 configuration string on at91rm9200
Hi, I am using kwikbyte at91rm9200 and I want to setup kgdb remote debugging. I have compiled a kernel with kgdb support for serial port (8250) debugging but I haven't figured out what the kernel boot...
—
|
15 years ago
|
— |