Wanted LSI 53C876 data sheet

I'm looking for a data sheet on an LSI chip. It is the 53C876 and is used as a dual channel SCSI controller.

Any ideas - I looked at the LSI site and was unable to find it, but perhaps I am looking in the wrong place. All I could find are drivers for Windows PCs to use SCSI cards based on that chip, which is not what I want.

I'm thinking of converting a couple of dual channel SCSI cards - one is single ended (SE) and the other high voltage differential (HVD), so the boards have one SE and one HVD channel on each board, rather than two of the same on the boards. I need both SE and HVD in a computer, but don't want to use two PCI slots.

--
Dave K

http://www.southminster-branch-line.org.uk/
 Click to see the full signature
Reply to
Dave (from the UK)
Loading thread data ...

I can post a copy to abse, would that be helpful?

--
 Thanks,
    - Win
Reply to
Winfield Hill

You have Mail...go get it

Reply to
kip

I have three sym53c876 documents. One is from Symbios Logic, dated 1996, quite detailed, 281 pages and 15MBytes in length.

--
 Thanks,
    - Win
Reply to
Winfield Hill

Thanks, but someone pointed me to an online version

formatting link
(from)
formatting link

It appears what I was thinking of doing (hacking a dual single ended and a dual high voltage differential boards to make a dual Se + HVD board) would be quite difficult, since the two PCB layouts of the Sun SCSI boards in question are quite different.

The SYM22810 (which looks identical to the Sun 375-0005 single ended board)

formatting link

and the SYM22802 (which I assume is the same as the Sun 375-0006 Sun HVD board, although I can't verify this)

formatting link

are far from the same as you can see.

I've verified the 53C876 chip will do both SE and differential, but getting the other chips hooked up requires more than simply swapping a few chips from one board to another.

I'd like to find out how on earth a tape drive can be fitted in my computer (Sun Ultra 80). A DDS-3 tape was available as an option, but I can't see if it needed a SCSI board.

It is a bit silly really, as the motherboard has two single ended SCSI controllers, but I can't see how to route either of them to a tape drive. One does the two internal disks and internal CD, but with no obvious way of putting a tape drive on there. The other feeds a connector on the rear, with again no obvious way of attaching an internal tape drive to that.

There are spaces for 3 internal units - a floppy, CD and one other.

--
Dave K

http://www.southminster-branch-line.org.uk/
 Click to see the full signature
Reply to
Dave (from the UK)

You make a new ribbon cable with an extra connector of course ! Easy.

Graham

Reply to
Pooh Bear

I don't think it is as easy as that.

The 68-pin connector on the rear panel is almost certainly mounted on the motherboard, with no cable.

The other channel, which feeds the SCSI backplane for the two 80 pin SCA drives would need more than 68 pins, so will not be 68-pins.

I can't switch the machine off now to look and its impossible to remove the side panel without it tripping a micro switch that disables the ouput form the power supply.

As such, I don't believe there are any internal 68-pin SCSI connectors.

Someone else hit this problem in a Sun Blade 2000 computer.

formatting link

which is a somewhat similar. Mine is somewhat older, but quad processors, whilst that is somewhat never and dual processors.

It would appear from the replies he got that for DDS-4, you can use a narrow connector (50 pin), as the data is only transfered at about 5 MB/s maximum.

--
Dave K

http://www.southminster-branch-line.org.uk/
 Click to see the full signature
Reply to
Dave (from the UK)

formatting link

I'm still confused. You can buy SCA to 68-pin adapters, and 68pin to 50-pin adapters. The big problem would be that the bus would run at the speed of the slowest device.

Reply to
carl0s

The SCSI path is:

motherboard ------>SCA backplane ---->CD-ROM and terminator.

The cable between the motherboard and the SCA backplane does not have nice simple 68-pin cables with standard connectors.

The cable between the SCA backplane and the terminator (which is part of the cable) is possibly 68-conductors, but has no standard 68-pin connector on the SCA backplane.

The end of the cable has a molded conversion to 50 pins and terminator. The cable might be 68 conductors to the terminator, but I don't know. There is no reason it needs to be, and the wiring could be non-standard. So crimping a 68-pin connector here might be risky, especially as a replacement cable is $400.

I found this manual (page Figure 4-1, Page 4-2 or page 26 in the PDF) shows the Sun solution, which is a 50 pin extension cable.

formatting link

However, that is not cheap ($70, plus shipping) considering it is only 3

50-pin IDC connectors on a short length of 50-connector cable. I think I'll make one of them myself. I can get the parts for about £5 (around $7), so it is 10% of the price of buying one.
--
Dave K

http://www.southminster-branch-line.org.uk/
 Click to see the full signature
Reply to
Dave (from the UK)

ElectronDepot website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.