Electronics Repair

  1. Home
  2. Electronics Repair
21789 Threads Posts
to

Worth reading in Electronics Repair

Wanted: Vintage Tektronix Test Equipment

Hello Everyone, I'm on the hunt for some vintage Tektronix test equipment (400-series and 500-series oscilloscopes, cal...
4 comments posted 15yrs
posted by cchhrriiss11
4 comments posted 15yrs posted by cchhrriiss11

WTD: B&K manual for 1074 Yoke/Flyback analyzer

How's that for ancient? Have one of these and would like to be able to use it to service some of the older B&W or colou...
2 comments posted 15yrs
posted by spam
2 comments posted 15yrs posted by spam

Mitsubishi U65 VCR component ident question!

I've repaired the p.s. in my U65 that recently smoked (caught it before it went into complete meltdown thankfully!!!) a...
3 comments posted 15yrs
posted by nuttyneo
3 comments posted 15yrs posted by nuttyneo

Microwave waveguide

Microwave oven was arcing, so after reading the repair faq I learned that the wave guide cover was a possible source. S...
3 comments posted 15yrs
posted by new.trail.rider
3 comments posted 15yrs posted by new.trail.rider

TV aerial gizmo

Is there a gizmo which can connect to my living room wall TV aerial socket which will send the TV signal to my bedroom...
10 comments posted 15yrs
posted by mikehh.89c0de9
10 comments posted 15yrs posted by mikehh.89c0de9

Sony screwdriver and bit.

I got this set a while ago, probably in the early 1980's. It's a Sony combo screwdriver and bit. The photos are here: h...
4 comments posted 15yrs
posted by farberbear.unspam
4 comments posted 15yrs posted by farberbear.unspam

Flyback xfmr cores - where to buy

I'm trying to repair an LCD monitor with a bad flyback power supply stage. I'll need to wind a new transformer. What's...
2 comments posted 15yrs
posted by paul
2 comments posted 15yrs posted by paul

Samsung P43D450 Panel Needed

Mr. Customer dropped his new Samsung TV and cracked the plasma panel (BN-96-17356A). I am getting quotes from US$280 to...
0 comments posted 15yrs
posted by klay
0 comments posted 15yrs posted by klay

Speaker voice coil windings

What is the difference between N turns of wire of cross-sectional area A and 2 parallel coils of N turns and wire area A...
5 comments posted 15yrs
posted by diverse
5 comments posted 15yrs posted by diverse

Cordless iron

Thinking about picking up a cordless solder iron again - mostly for audio cable work. Anyone have any suggestions? Well...
12 comments posted 15yrs
posted by donovandigital
12 comments posted 15yrs posted by donovandigital

OT: electric motor brush WTF

Sorry for posting this here, but you guys are a technical lot. I fixed my ASKO washer today by finding that one of the...
17 comments posted 15yrs
posted by landotter
17 comments posted 15yrs posted by landotter

How to resolder a cold solder connection?

http://www.tegger.com/hondafaq/mainrelayfix/index.html Next to the fourth picture, it says: "Removal of old solder As m...
48 comments posted 15yrs
posted by NONONOmisc07
48 comments posted 15yrs posted by NONONOmisc07

Panasonic NNT785SF Inverter board IGBT replacement

I am working a Panasonic NNT785SF microwave that always turns off after working for 2 seconds when it's on. Now I found...
1 comments posted 15yrs
posted by anson.stuggart
1 comments posted 15yrs posted by anson.stuggart