Field-Programmable Gate Arrays

15255 Threads Posts
to

NIOS and OCI

This is from memory since work doesn't have access to newsgroups so here goes. We have a Stratrix development board wit...
5 comments posted 23yrs
posted by nospam
5 comments posted 23yrs posted by nospam

Reducing Clock Speed

Hi All I have a Nios Development Board that has a crystal osciallating at 50MHz. This is correct as I have seen the wav...
9 comments posted 23yrs
posted by nospam
9 comments posted 23yrs posted by nospam

Nanometers, Gigahertz, and Femtoseconds

That is the title of my keynote address at the FPGA Developers' Forum, Oct 21/22, in London. If you can make the place...
0 comments posted 23yrs
posted by peter
0 comments posted 23yrs posted by peter

Strange synthesis behavior from Quartus II 2.2

Hi, I have a design that was compiled in Quartus II 2.0 (SP2) and used 22,000 logic elements on the APEX20K1500E device...
4 comments posted 23yrs
posted by prashantj
4 comments posted 23yrs posted by prashantj

Quartus Usability Feedback

Quartus II 4.0 contains several improvements to make it easier to use, for Max+Plus II users. We are interested in test...
0 comments posted 23yrs
posted by sdatta
0 comments posted 23yrs posted by sdatta

Graphics rendering

I know about the various algorithms to draw lines, circles, etc. All of these pretty much rely on painting onto a frame...
32 comments posted 23yrs
posted by 0_0_0_0_
32 comments posted 23yrs posted by 0_0_0_0_

chipscope pro and jtag

Hi , my question is about using/modifiying ChipScope Pro: I have a direct access to the jtag pins through my own device...
8 comments posted 23yrs
posted by tirmen
8 comments posted 23yrs posted by tirmen

Transition from Virtex-E to Virtex-II

As we are transitioning from Virtex-E to Virtex-II, we have the following excess inventory to sell. XCV2000E-6BG560C 44...
0 comments posted 23yrs
posted by banktrade2002
0 comments posted 23yrs posted by banktrade2002

Synchronous Binary counter question.

Hello All OK Im a bit confused. the verilog code always @(posedge CLK or posedge CLR) begin if (CLR) Q
11 comments posted 23yrs
posted by dgleeson-2
11 comments posted 23yrs posted by dgleeson-2

on the fly Reconfig

I am trying to use the embedded ppc in Xilinx Virtex 2 pro FPGA to reconfigure the same. I have gone thro the embedded...
0 comments posted 23yrs
posted by ramnathanm
0 comments posted 23yrs posted by ramnathanm

Free WebPack 6.1i Download Available Now for Spartan-3

Just FYI, the free WebPack 6.1i is now available and supports the Spartan-3 XC3S50, XC3S200, and the XC3S400. Also, the...
9 comments posted 23yrs
posted by steve.knappNO#SPAM
9 comments posted 23yrs posted by steve.knappNO#SPAM

Speed of various elements in the spartan3

Perhaps I just missed what I am looking for, but I cannot seem to find any indication of the speed of most elements wit...
0 comments posted 23yrs
posted by hicksthe
0 comments posted 23yrs posted by hicksthe

Portable computer for FPGA/CPLD tools

Hello, I would like to know if someone have evaluated the performance with FPGA software tools of the new Intel Centrin...
3 comments posted 23yrs
posted by javodv
3 comments posted 23yrs posted by javodv

Reading from FPGA Issue

Hi Guys I am trying to read 36 signal one by one from FPGA using different addresses and these signal are of 3 bits len...
5 comments posted 23yrs
posted by fpga_uk
5 comments posted 23yrs posted by fpga_uk