Embedded Programming

Cable needed: 4 twisted pairs, individually shielded with overall shield

Hi, I have an application needing a cable with the following rough requirements: -4 twisted pairs, individually shielde...

0 comments posted 23yrs

posted by mph

0 comments posted 23yrs posted by mph

Hitachi LM238XB Display

hi! i've got a Hitachi LM238XB display and no idea how to control it. it has a 20 and a 10 pinning connector onboard. I...

1 comments posted 23yrs

posted by eyeofra

1 comments posted 23yrs posted by eyeofra

Execution and Reading from parallel EEPROM

Hi, I am working with parallel EEPROM and the application is as follows: The code will be executed from parallel EEPROM...

11 comments posted 23yrs

posted by reddy_laxmi

11 comments posted 23yrs posted by reddy_laxmi

Problem with Mcore 2114 flash programming or ???

Hello. Tools : CodeWarrior V2.5 for MCORE and BDI1000 ABATRON It's my second project on MCORE 2114 ; on my first projec...

0 comments posted 23yrs

posted by lionel.dx

0 comments posted 23yrs posted by lionel.dx

__ASM() and *.s33 to *.C files (continued)

> In news group comp.lang.c in article > Kev>> snipped-for-privacy@tesco.net wrote: >> Inlining assembler in a *.c file...

2 comments posted 23yrs

posted by robin.pain

2 comments posted 23yrs posted by robin.pain

u-boot (0.4.0) lubbock platform -> LCD howto?

I need to get the LCD thingy to work on a lubbock platform (PXA 250) so i defined: CONFIG_LCD 1 CONFIG_SHARP_Lm8V 1 in...

0 comments posted 23yrs

posted by 36214

0 comments posted 23yrs posted by 36214

Reset on ATMEGA8535 oddity

I've used the simple cap/resistor RC circuit on the reset line of my AVR boards forever quite reliably to hold the AVR...

6 comments posted 23yrs

posted by dlc

6 comments posted 23yrs posted by dlc

Moving from assembly code to C

Any experiences with "refactoring" assembly code to C or C++? A different target CPU (due to obsolescence and future up...

15 comments posted 23yrs

posted by prenom_nomus

15 comments posted 23yrs posted by prenom_nomus

Massive RS-232 required - any x86 boards out there?

Hi folks, I am just getting into embedded work and have the following requirements which seem to be very hard to meet....

9 comments posted 23yrs

posted by harnek

9 comments posted 23yrs posted by harnek

How to store data?

Hi Group! I am new to embedded systems. I have an application to develop. In that i need to maintain a data storage, un...

4 comments posted 23yrs

posted by shabana_rizvi

4 comments posted 23yrs posted by shabana_rizvi

WTB: Motorola Sandpoint PowerPC 755 eval platform

Anyone know where I can get one? Turns out the Motorola site refers one to third parties that don't have it. Thx, Kyle

2 comments posted 23yrs

posted by kyleNOSPAM

2 comments posted 23yrs posted by kyleNOSPAM

Toronto parts stores?

Does anyone know of any good parts places in Toronto? It doesn't have to be fancy stuff, just glue chips, perf-boards,...

7 comments posted 23yrs

posted by androidcat99

7 comments posted 23yrs posted by androidcat99

Problem with 16 bit AVR register (temp register oddness)

I need to use the 16 bit counter/timer (AT90S2313-10) and fully understand the order of reads and writes to ensure atom...

4 comments posted 23yrs

posted by aacarola

4 comments posted 23yrs posted by aacarola

I want the compiler to use my floating point multiply function

Hi, I compiled the Minix floating point library for my 16-bit micro. I got no warnings, but I can't have the micro use...

9 comments posted 23yrs

posted by enrico.migliore

9 comments posted 23yrs posted by enrico.migliore

embedded device->rs232->XP (kinda OT)

A device I wrote code for a while back required a serial code download from a Windows based download program. I develop...

16 comments posted 23yrs

posted by newton

16 comments posted 23yrs posted by newton