Even PCBs are written in "Engrish" now

Ugghh..annoying pop ups on that link..

DANDER HIGH VOLTAGE Ha! Like cat dander.

Yup..Wafer doesn't make any sense to me. It's not even Wafer1.. What's the standard/com silkscreen for connectors? CONN1 ?

D from BC British Columbia Canada

If there's any standard it's J1 ('jack'), and if you're calling out connections in wiring harnesses the mating wire is P1 (plug, with matching number).

Direct l>Ugghh..annoying pop ups on that link..

Sounds like you still use The World's Worst Browser. A modern browser will have an integral Pop-up Blocker. Gecko-based browsers have a NoScript extension available.

Ice cream context in the machine translator? Con1 -> Cone -> Wafer

-- General electronic repairs, most things repaired, other than TVs and PCs

Diverse Devices, Southampton, England

You cannot see the thermistor attached to that connector and plugged into that socket marked "wafer"?

In an ideal world, sure. In the real world, there are jack/plug moniker mismatches all the time.

My favourite is one I found in an old guitar pedal. There was a drawing of the 9 volt battery and its connector, and the helpful text "connect battery to battersnap"

Gareth.

Sometimes you are a bit dopey.

If there is no "wafer 2" there does not need to be a "wafer 1", so "wafer" is perfectly fine.

Just as, if there is not more then one transformer on an assembly, there does not need to be any numerical designation made in referencing the part. It can be referred to as merely "transformer", and will be perfectly correct.

Normally, the connector/plug pair would be so designated, ie "J1" and "P1" or other abbreviated terms such as that which you used, if the connector were part of a remote attachment, as in the case of interconnecting cables.

Since the connector/plug pair are being utilized as a "plug" for a pre-fabricated "part", that being the "wafer", then the "wafer" designator is all that is needed as long as all intended to ever build or service it know what the moniker refers to.

Proprietary systems use this so that dopey repair dudes can deal with their information overload easier... tee hee hee...

For the most happiness times in Engrish, pleasing to be moved most forward into

Isn't it the way fer power to come in? or else the way fer it to go out? Probably they just omitted the apostrophe from the contracted form wa'fer.

You guys are dopes. One can clearly see the thermistor in place in that connector header. Can't see it? Then, you shouldn't even be in the thread.

That's the wafer you to connect wires to the PCB. ;-)

I apologize for the poor photo, here is a higher resolution photo of the same PCB from a different angle (without the annoying popups):

Is that on a monitor? Is that a degaussing coil?

"Way fer" magnetic distortion to go out...

On Wed, 11 Jun 2008 03:45:33 GMT, snipped-for-privacy@nospam.com (Tom) put finger to keyboard and composed:

I'm trying to understand the reason that an "S" is appended to resistors, capacitors, and diodes, ie RS2, CS4, DS2.

As for WAFER, if you're looking for a typo on a QWERTY keyboard, then possibilities include SAFER, WAGER, WATER, WAVER, WADER. However, I'll wager it would be safer to keep water out of the power supply. I'd also waver before touching the power connector, although wearing rubber waders may afford some protection.

- Franc Zabkar

Usually because the designer drew the power supply schematic separately from the main board and the PCB designer had to add a spurious character (S for supply)to distinguish R5 in the parts list from RS5 etc. Worst still is the designer who gives you one sheet and says he wants 6 channels on the same pcb (he gets R5 R105 R205 etc after a lot of agravation).

Geo

Wafer connector:

Hope This Helps! Rich

So, those are all a "way" "fer" you to connect stuff up.

If you get unwanted/annoying pop-ups get a browser like Firefox that allows you to block these...I never see pop-ups except for web sites that I specifically allow them on (some of my order sites, banks, etc.).

John :-#)#