27,100. No kidding. The car is hardly driven.
I hadn't thought about that. Thanks.
27,100. No kidding. The car is hardly driven.
I hadn't thought about that. Thanks.
I didn't have much trouble fixing my Toyota's carb and got only 2 of its 14 vacuum hoses wrong (taking clear photos or making sketches is a good idea). The instructions included with the aftermarket rebuild kit were better than those found in Chilton and Haynes manuals and almost equal to the factory manual (but there's a book specifically about Rochester carbs that's probably better than anything). OTOH aftermarket rebuild kits may be noticeably inferior in quality, and with my first kit, by Tomco, the rubber parts turned rock hard after five years, and the float valve clogged because it lacked a filter screen to trap the bits of rubber that flaked off the fuel line. The float valve clogged as a result, yet Tomco advertrised that its float valves were more clog resistant than others'.
I was to told to not disassemble the carb any further than necessary. For example, the choke and throttle plates should be left alone, as should any adjustment screws, but if it's necessary to touch the latter, count the exact number of turns of their original settings because a lot of times there's no simple way to adjust them correctly, i.e., to set the idle mixture you may be instructed to use an exhaust gas analyzer.
The web site says their R-12a substitute for Freon R-12 contains propane, and propane/butane blends are known to cool well in systems originally made for R-12. But I'd never try that since I don't like explosions in my car, and while Duracool downplays the danger, I doubt the refrigeration industry would have made such major efforts in the early 20th century to develop nontoxic, nonflammable refrigerants if the refrigerants available at the time had been reasonably safe.
Actually they were more concerned about poisoning the customer. Methyl Chloride and ammonia are pretty nasty. The stuff in Duracool is pretty much what is in a can of instant whipped cream - or anything else like that. With
12 gallons of gas under the car, 12 oz of butane in the engine compartment doesn't worry me.
At the very least, put in AC brand spark plugs. Regular copper-cored ACs are fine; there's no need for expensive platinum plugs.. The other parts, regardless fo brand, should be OK, except for any inductive supressive wires. If you have such wires (each measures only a few hundred ohms, some brands are Borg-Warner "Kool Wire" and Splitfire), replace them with regular resistive supressive wires (thousands of ohms per wire). Unless the distributor rotor or cap has developed hairline cracks from high voltage, there's no need to replace either, unless the rotor is shorter than the original (I've seen that).
I mistakenly thought your idle speed was wavering, but since it's rock steady and the CO and NOx are low, I can't imagine there being a fuel system problem, and I doubt there are even vacuum leaks. So I have to believe the trouble lies with the ignition. Someone suggested the evaporative emissions system, but I believe it would also raise the CO since it vents the fuel vapors into the intake and makes the mixture richer.
It's good you don't have a leaky Ford system or you could need a recharge every 2 years.
Here's a web site for ALDL information from GM computers, and they say it was available as far back as 1982 with the CLCC system. I don't know if that's the same as CCC:
The propellant for whipped cream is usually nitrous oxide, as many people who've used it for cheap thrills have discovered. If propane/butane was so safe, why haven't any makers of autos, refrigerators, or air conditioners used it in the past several decades?
Hey, I didn't know I could do that. My car is not at either of those links, so I will have to do some snooping to find a page right for me. I'm not sure how I process the data stream once I have it.
When I take the emissions test - rather, when my car takes the emissions test - it is backed onto a treadmill, and the engine is revved up so that the car is going either 15 or 25 miles per hour. The OBD II-equipped cars don't have to go through this procedure. A cable is plugged into their computer's port, and the data is (are?) downloaded to the emissions analyzer. Even though their test is much less complicated than mine, the $28 fee still applies.
Thanks a lot for the information.
I should add: when my car is tested, it is connected to the test equipment in three ways.
1) The rear (driving) tires are on the treadmill, providing speed information. 2) An exhaust gas analyzer probe is inserted into the tail pipe, providing exhaust gas information. 3) An inductive pickup is clipped over one of the spark plug wires, providing engine rpm information.There is no connection made between the ALDL port and the test equipment.
"Today, almost all aerosol cans contain alternative propellants, such as liquefied petroleum gas, which do not pose as serious a threat to the environment".
The Plain Man's Guide to Aerosols
As for what and why, there's a safety difference between what is used in a domicile and what is under the hood. It is possible that even the new refrigerants will wind up being banned in time.
I'm not very impressed with that Cadillac dealer because if you paid them they should have given a very specific diagnosis, like, "The problem is X, and the car will run right if Y is repaired/replaced," where Y isn't something like an entire new engine or car. What tests did the dealer perform? It's apparent that they didn't read out the ALDL data, but did they hook up an ignition oscilloscope, measure the exhaust emissions, check for vacuum leaks, or measure engine compression or leakage? Skill levels of mechanics can vary greatly. I once had a Chevy where the Chevy dealer that leased it couldn't solve a pinging problem, and after charging $240 (about $500 in today's dollars) they merely told me to run high octane gasoline. On the way home, on a whim I decided to stop at a Buick dealer, and they solved the problem in 20 minutes by changing a small restrictor or check valve in a vacuum line. That wasn't 20 minutes of repair time but 20 minutes from drive-in to drive-out.
I haven't taken the car to the Cadillac dealer yet. All five of the emissions tests it has failed have been at a nearby gas station. Since the next test will cost me $28 no matter where it is performed, I will take it to the Cadillac dealer then.
No one at the Cadillac dealer has worked on my car. I have gone up there and hit them up for some free advice on how I should proceed to repair my car, but I am the one turning the wrenches.
No. I have not asked them to do any of that.
I think that all GMs from the early through the remainder of the decade used the CCC system, which just means that they had a computer managing certain aspects of the engine, transmission, and transmission.
The CCC system then seems to be available in a variety of flavors. Some cars had throttle body injection, some had multi-port injection, and some used a carburetor. It seems to me that the cars with carburetors were referred to as being of the CLCC variety.
Note that every system has an "I" in it somewhere other than the CLCC system. I believe the "I" stands for injection and the "C" for carburetor.
Yikes. That's not right. The carburetor does indeed have a mixture control solenoid. Ten times per second, acting on readings from, among other sensors, the O2 sensor, it adjusts the air-fuel mixture.
Wow, was that ever a wrong thing to say. I apologize for that.
I got the instructions from a tech at the Cadillac dealer on how to use a dwell meter to check the operation of the mixture contol solenoid.
I found a more appropriate port at which to measure my vacuum. It is about 19-20", but it is not steady. There is a vacuum leak somewhere in all those hoses. Those of you who said I had a vacuum leak, take a bow.
I dread vacuum leaks. They can take forever to find.
Well, it's not that steady. It does waver, but not wildly. If you put your hand over the carburetor throat to block off air, the speed increases, and the amount of vacuum goes up too.
Right. I obviously don't know your car or carb being UK based, but SU in the UK produced electronically controlled carbs as a last ditch stand against injection before ceasing production. They used stepper motors for both idle and mixture control, and worked extremely well - while they worked, that is. Many have been converted back to 'manual' ;-)
Spraying with something like WD40 can help while a helper observes the exhaust. If this gets drawn in and burnt, you'll get smoke.
Is the heater/AC controlled anywhere by vacuum devices? The brake servo? Auto box? Remove all these feeds and blank off the outlets. But don't forget the engine crankcase breather system too when checking for leaks.
The Rochester Quadrajet on this car works, essentially, like all the other Rochester Quadrajets - venturis, float bowls, metering rods, idle circuits - same old stuff. The mixture control solenoid and throttle position sensor are different, though.
Yes, there are systems that run on vacuum signals. The cruise control is vacuum actuated, and the heater controls send a vacuum to motors that open or close doors to direct heated air to foot-level vents or face-level vents in the passenger compartment.
I was getting an erroneous vacuum reading, because I had connected my vacuum gauge downstream of a check valve that sent vacuum to a storage tank that was part of the heater control system and cruise control. Even with the engine off, vacuum was present. That would have tipped me off right away, but I had disconnected my gauge with the engine running and did not note that effect. With the gauge connected upstream of the check valve (that is, between the intake manifold and valve), I now get a reading that better reflects the actual state of the vacuum. The vacuum is still at a good level, about 20", but the needle is twitching at about 10 Hertz, which is (incidentally?) the rate at which the mixture control solenoid is refreshed.
Right now, I have the gauge on a long enough hose that I can sit in the driver's seat and watch it. The cruise control and heater controls are disconnected. Since this did not alter the stalling at idle, those circuits can be eliminated as a cause.
I can't recall whether the TH200R4 transmission has a vacuum modulator or not. That's easily enough established.
Thanks for writing.
Have something to add? Share your thoughts — no account required.
Ask the community — no account required