[OT] Automotive emission controls

Oct 05, 2006 56 Replies

GM sells this stuff called "Top Engine Cleaner." I've used it before, a few years back, on this car. In August, the Cadillac techs felt it would be a waste of money, but after I flunked the test again on the

4th, one of them suggested pouring in a can. I bought a can and poured it in, following the instructions on the can religiously. Huge clouds of smoke came out with the Top Engine Cleaner in the combustion chambers, presumablyfrom the carbon being burned off.

The tech also said to take it out and "drive it hard." I've had some some other non-automotive chores that had to be done, so I've haven't got around to the brisk drive yet. I will do that.

Confirms my earlier diagnosis. It's running weak. Check first for air leaks anywhere in intake system and engine breathers. Only then check carb.

*I am a nobody, and nobody is perfect; therefore I am perfect* Dave Plowman dave@davenoise.co.uk London SW To e-mail, change noise into sound.

My auto service guy says the stuff does little or nothing.

If the stuff really removed carbon, it would be used as oven cleaner, less dangerous than lye.

Hmmm, too bad lye is hard on aluminum, maybe a can of "easy off" would remove the Carbon?

Did you change the oil before the test? That can make a lot of difference I'm told.

What specific car are we dealing with? There's many newsgroups that cater to just about every brand of car there is, and most have many helpful folks on them.

Do you mean "lean?" That would be the terminology used in the States. How do you account for the high intake manifold vacuum and the steady needle on the vacuum gauge?

I posed the novella about my car at the Usenet group rec.autos.tech.

formatting link

or

formatting link

Thanks again to everyone.

I, too, am leary of the "engine rebuild in a can" chemicals, but the old timers all swear by the stuff. It's mostly naptha.

Yes. Lower than normal CO and high HC is a classic symptom.

Do you know what the vacuum reading should be? However, if you're sure there are no leaks, sound like the carb is faulty. Presumably being a late type it has electronically controlled mixture and idle speed?

*If you're not part of the solution, you're part of the precipitate * Dave Plowman dave@davenoise.co.uk London SW To e-mail, change noise into sound.

21" with the needle steady, not wobbling, is considered good. It had been so long since I had last used one that I had to get on the Internet to look up how to go about using one.

How to Use and Interpret a Vacuum Gauge

formatting link

No. The Oldsmobile 5L/307 cid V8 is the last of the carbureted engines. The carburetor (US spelling) has a throttle position sensor, but everything about the carburetor's operation is mechanical, not electronic, unless there's something I'm overlooking.

Thanks.

"Beloved Leader" wrote in news: snipped-for-privacy@c28g2000cwb.googlegroups.com:

The only use for a throttle position sensor(TPS) is to electronically control the engine. If only the ignition timing,which will affect emissions.

Are you sure it's a carburetor and not just a throttle body with single port injection? Is the TPS wired up? Maybe somebody put the wrong carb on.

Jim Yanik jyanik at kua.net

Can you also post the CO2 and O2 readings? I won't know what they mean, but someone will.

I once glanced at the Haynes emissions manual and found it to be little mroe than a rehash of the emissions chapters from other Haynes books. It lacked the hundreds of pages of diagnostic tables found in the Mitchell and factory manuals. That community college may not only let you see the books but even fix your car at low cost, but don't be surprised if they want to keep it for a few days.

Are you using only GM ignition parts -- AC plugs, wires, rotor, and distributor cap? Some plugs don't substitute well, even when they're supposed to, and trick wires (magnetic supression, as opposed to resistive supression) can cause problems. I wouldn't even try AC Rapidfires, simply because they're not factory original equipment. Some brands of rotors and caps are made of bad plastic that cracks from high voltage. I realize you changed all the vacuum hoses, but did you check for vacuum leaks at the intake manifold gaskets and base of the carburetor by spraying there with choke cleaner?

Try injecting propane or choke cleaner into the air intake (leave air filter and cover in place -- prevents fires in case of spit back) for a few seconds. If the idle (set to about 550 RPM) smooths out (injecting chemicals will make it speed up by as much as 200 RPM), suspect a vacuum leak or a carburetor problem. The idle mixture solenoid has been troublesome in some feedback carbs. I don't know if there's any kind of idle speed regulation (throttle air bypass valve, throttle kicker or motor), but a carburetor problem may be completely unrelated to your high HC.

By the way, run the air conditioner compressor for at least 10 minutes in a row each week, even during the winter, to keep the shaft seal from drying out. You have a Freon R-12 system and don't want any of that gas to leak out, and you don't want to convert to R-134a the wrong way (cheap, quick conversions don't perform well and have high failure rates).

I don't see the purpose of top engine cleaner here, and I'm surprised a dealer mechanic would recommend it, at least not without first reading out the CCC data stream during engine operation to find any abnormalities (temperatures, barometric and manifold pressures, oxygen sensor voltage, throttle position, fuel mixture solenoid duty cycle, etc.).

Then presumably has an adjustment for the idle mixture?

*Can atheists get insurance for acts of God? * Dave Plowman dave@davenoise.co.uk London SW To e-mail, change noise into sound.

Totally, absolutely, positively, one hundred thousand, million, billion, trillion percent. The carbureted 307 was last used in the

1990-model cars. In 1991, GM replaced it with the FI 305.

Yes.

Not a chance. The car has been in the family since new. It has the factory carburetor.

No. The test equipment in use by the Commonwealth of Virginia does not test for CO2 or O2. I've provided all that I've got.

I'm not surprised by that.

Oh, yes, I do get to look at the library. I'd also like to talk to some of the instructors there. I still want to do the repairs myself, being of the "if you want the job done right, you've got to do it yourself" mentality. I also feel that I'd be a more meticulous mechanic than the

18- and 19-year olds taking the courses at the local CC.

No.

I can try that, using an unlit propane torch. Bear in mind that the idle's not rough, just low. Nonetheless, I find it hard to argue with such a sterling reading on my vacuum gauge. For the record, I'm getting my vacuum reading from a port that leads to the vacuum chamber for the car's vacuum-actuated cruise control.

Ice cold, baby. The real deal. The good stuff.

The oldtimers like the stuff. Remember that the CCC system is ancient, being of the same vintage as 8088-based computers. It is way obsolete compared to OBD II. There is no such thing as a CCC data stream. It does not provide the sort of information you mention. My code scanner does no more than short two terminals. By so doing, I can count flashes on the "check engine light" that direct me to any suspect sensors. The CCC system does not, as I have learned, make note of vacuum leaks.

I'm getting more responses at sci.electronics.repair and sci.environment than I am at rec.autos.tech.

Thanks for writing, one and all.

Yes, but they're sealed. Federal law and so forth. I mean, no one would ever know, but to get at the idle mixture adjustment screws, I'd have to take the carburetor off and drill out the sealing plugs. There are quite a few connections to the carburetor, so its removal is a major undertaking.

On UK cars with this feature (for export to the US, etc) it's much easier than that to remove the plug.

Yup. Other thing to check for if the mixture is 'lean' at idle while otherwise ok is air leaks round the buttefly spindle bushes. Smear some grease round the outside for a temporary 'cure'. If the idle speed then goes to normal you've got the reason.

*Why is the time of day with the slowest traffic called rush hour? Dave Plowman dave@davenoise.co.uk London SW To e-mail, change noise into sound.

What about

formatting link
??

"Beloved Leader" wrote in news: snipped-for-privacy@i3g2000cwc.googlegroups.com:

Well,what do you think the car does with that data?

Jim Yanik jyanik at kua.net

The data from the throttle position sensor is sent to the ECM, along with the data from all the other sensors. The ECM uses that data to control, in accordance with a look-up table in the ECM's memory, the setting or position of a variety of actuators.

You didn't mention the mileage on the engine. Consider that older engines tend to have trouble with valve guide seals, which harden with age. A bit of extra oil will seep past into the intake and may add to your HC emissions, especially at low speeds when the throttle is almost closed. Also, your rings may be allowing some oil into the cylinders. One final point to check, if you haven't already done so, would be your PCV valve, which should close at high vacuum, but may be so dirty or worn that it is not doing so, thus allowing excessive amounts of gas into the intake manifold from the crankcase.

Eric Swanson --- E-mail address: e_swanson(at)skybest.com :-) --------------------------------------------------------------

Join the Discussion

Have something to add? Share your thoughts — no account required.

Didn't find your answer?

Ask the community — no account required