How do I drag multiple vias without breaking the nets?

Nov 18, 2026 Last reply: 20 hours ago 4 Replies

First reply

FixerSawdust

Bad news: dragging multiple vias with their nets still attached just isn't something KiCad can do cleanly. I've hit exactly the same wall you're describing, with the drag tool losing the grid and DRC throwing errors every which way while I'm mid-move. The usual answer from…

Read the full reply

This feels like it should be easy but I just can't figure it out. I've got 3 vias labeled MOSI, MISO and SCK sitting on my layout, and all I want is to nudge them a few millimeters to the left while the nets stay attached to them. Surely there's a way to do that without redoing everythign around them? The regular drag tool isn't cutting it. When I try to drag the vias they won't snap back onto the grid, and the DRC seems to lose its mind while I'm moving them, throwing errors all over the place. It makes the whole thing feel jittery and impossible to place cleanly. Right now my workaround has been to unroute most of the traces near them, move the vias, then reroute from scratch. That works but it's getting relly taxing when I'm only trying to shift a few vias over a tiny distance. Is there some trick or setting I'm missing here? Even a pointer in the right direction would help a lot.


Bad news: dragging multiple vias with their nets still attached just isn't something KiCad can do cleanly. I've hit exactly the same wall you're describing, with the drag tool losing the grid and DRC throwing errors every which way while I'm mid-move. The usual answer from experienced KiCad users is the same: forget dragging, just move the vias and reroute the tracks afterwards. I know that sounds like what you've already been doing, but there's a way to make it way less painful than unrouting everything first. Here's the trick. Select your three MOSI, MISO and SCK vias along with the traces you want to keep, hit M to move them, and then use the keyboard arrow keys to shift everything to the left instead of moving with the mouse. The arrow keys keep the whole selection locked to the grid, which sidesteps that jittery screen-pixel-to-grid conversion you get when dragging with the mouse. That's what makes it feel impossible to place cleanly, and it goes away completely with the keyboard. And if the DRC is fighting you the whole way, just turn it off, do the move, then turn it back on again once everything is sitting where you want it. All those errors flying around mid-move are just noise from tracks being temporarily violated, so there's no harm in silencing it for the few seconds the move takes.

Another option is to highlight the vias and group them, so they behave as one object and get moved together in a single action instead of you nudging three separate items.

Either way you'll end up rerouting a bit at the end, but with the M-plus-arrow-keys approach you're rerouting a short section rather than tearing up the whole area around the vias. I honestly wish KiCad handled this properly, because shifting a small cluster like those three should be a two-second job. It's one of the things I keep hoping gets improved in a future version.

Just joined this forum and I'm glad I found this thread, because I've been doing the same unroute-and-reroute dance on my own board and it's driving me nuts. Your screenshot looks a lot like my layout, blue tracks on one side going to pads on the other, so this is exactly the mess I keep making for myself. The M plus arrow keys trick makes sense now that I see where the jitter comes from. One thing I'm stuck on though: when you group the vias so they move as one object, do the nets stay attached to them, or is that only for the move itself?

The grouping option is the one I lean on most. I had a similar little cluster of vias feeding an SPI bus on one of my boards, and grouping them meant the whole set moved as a single object instead of three items I kept having to reselect. One pass to set it up and every nudge after that was a single action. Looking at your photo, that red fan-out to the pads on the right is tight enough that I'd want all three shifting together rather than one at a time. Does the selection filter panel on the right side give you trouble when you're trying to grab just the vias and nothing else?

Yeah the arrow keys thing was the missing piece for me too. I'd been fighting the mouse drag for ages and never thought to just let go of it. One thing I'd check on your board, looking at the photo, is that the shift distance lines up with your grid size, since those blue-to-red transitions at the vias look tight enough that even one grid step off could mean rerouting more than you want. Out of curiosity, are you moving all three in one selection or one at a time? I've only ever nudged single vias like this and I'm wondering if the multi-select holds together as cleanly.

Join the Discussion

Have something to add? Share your thoughts — no account required.

Didn't find your answer?

Ask the community — no account required