Embedded Programming

Mode Switching for MIPS

Hi all, Does anyone know of the instruction to switch modes/generate an interrupt on a MIPS target. This is for GNU tool...

2 comments posted 21yrs

posted by mipshelp

2 comments posted 21yrs posted by mipshelp

IDE mode Compact Flash problems...

I have an compact flash attached to an IDECF adapter that boots fine in one motherboard but isn't recgonized as a hard...

13 comments posted 21yrs

posted by pm940

13 comments posted 21yrs posted by pm940

Looking for advice on "9 bit" UART SBC

I am looking for an SBC that has a "9 bit" UART. Are there any references or companies anyone can steer me towards. Than...

1 comments posted 21yrs

posted by alijsyed

1 comments posted 21yrs posted by alijsyed

mixing C++ and assembler modules with the MSP430

Hi everybody. My problem is when i try to mixing C++ and assembler modules. I ca mixing C and assembler modules thank t...

2 comments posted 21yrs

posted by el_777

2 comments posted 21yrs posted by el_777

Slightly OT: Database for embedded loggers

Hi all, I have a logging product where the data is downloaded serially over an RS232 or ethernet connection. Typically...

3 comments posted 21yrs

posted by acqua

3 comments posted 21yrs posted by acqua

High speed MCU

Hi, Could anyone introduce me some high speed MCU with either 8 bits or 16 bits? But the speed is better to be 50MHz or...

2 comments posted 21yrs

posted by eehobbyist

2 comments posted 21yrs posted by eehobbyist

My understanding of stack, is it right?

If there are two register A and B in microcontroller, I use PUSH A, PUSH B and then use POP A, POP B, what will happen?...

12 comments posted 21yrs

posted by persevreman

12 comments posted 21yrs posted by persevreman

BiskyMisky

BiskyMisky www.biskymisky.com

1 comments posted 21yrs

posted by fidelerol

1 comments posted 21yrs posted by fidelerol

C6x DMA: using dma_int0 to trigger a dma transaction on dma1

TI C6x question here: the dma channels on the C6x can be setup such that they are synchronized to a number of events (3...

1 comments posted 21yrs

posted by him

1 comments posted 21yrs posted by him

DSP Group TeakLite DSP Board

I've pulled a DSP Group Teak Lite DSP development board out of the bin at work. It's about 3-4 years old. Their web sit...

0 comments posted 21yrs

posted by AlfieNoakes

0 comments posted 21yrs posted by AlfieNoakes

Problem with USB enumeration... -> now with link to CATC trace...

Hello, i have a self developed device which has problem with USB device enumeration (posted this already a while ago)....

0 comments posted 21yrs

posted by Martin.Maurer

0 comments posted 21yrs posted by Martin.Maurer

EDK IPIF Core

I am simulating a IPIF + user core using the BFM simulation model and in my test I can succesfully write to the WFIFO (...

0 comments posted 21yrs

posted by nrivera.eng

0 comments posted 21yrs posted by nrivera.eng

How to build your optical "mouse"?

Is there an "open" circuit design using optical mouse princible (I would guess it is optical flow) to monitor from 10-20...

1 comments posted 21yrs

posted by landy

1 comments posted 21yrs posted by landy

Microchip looses the plot ?

This in the news: "Microchip sues Zilog over 8-pin microcontrollers" and it's not April 1st ? Microchip used to be an e...

49 comments posted 21yrs

posted by no.spam

49 comments posted 21yrs posted by no.spam

Virtex 2 Pro and PPC405

I have been looking around for a while. I dont want to use the EDK from Xilinx. Is there any free c compiler for ppc405...

2 comments posted 21yrs

posted by cumulusnimbus

2 comments posted 21yrs posted by cumulusnimbus