Embedded Programming

AVR32 Development Tools?

Does anyone know of any third party development tools for the Atmel AVR32 family besides IAR? We just got in some EVK11...

5 comments posted 19yrs

posted by StephensDigital

5 comments posted 19yrs posted by StephensDigital

What makes an IDE device bootable

Greetings - I am hoping to throw out the CF cards that our systems are currently booting off of and replace them with a...

2 comments posted 19yrs

posted by nleahcim

2 comments posted 19yrs posted by nleahcim

DAC Drivers

Hello Everyone, I am very new to DAC. I am writing drivers for DAC. How should i start writing DAC drivers. I am having...

4 comments posted 19yrs

posted by forqueries

4 comments posted 19yrs posted by forqueries

mmu on pxa255

Hi, I'm looking for example of setting mmu and page table for pxa255 processor. I've tryed to use macros like in ecos b...

0 comments posted 19yrs

posted by armuser

0 comments posted 19yrs posted by armuser

small utility to merge selected data from two hex files

All, I wrote a small tool for my own use, which some of you may find useful also. It allows to merge selected address r...

3 comments posted 19yrs

posted by tomtorfs

3 comments posted 19yrs posted by tomtorfs

TSB82AA2 link layer controller

Hi, I am stuck! I am sure many are aware that a TSB82AA2 work as an interface between PCI bus and a Phy layer chip. My...

1 comments posted 19yrs

posted by ameliaw.azman

1 comments posted 19yrs posted by ameliaw.azman

I2C Problem

Hi all, I am trying to drive an I2C device from a windows CE board, unfortunately without success. I am trying the foll...

4 comments posted 19yrs

posted by carmelgafa

4 comments posted 19yrs posted by carmelgafa

How many resistor on CAN Bus?

Hi, I'm working with a CAN bus based on CANOPEN protocol. My bus lenght is about 200m and the speed is 250Kb/s. I have...

9 comments posted 19yrs

posted by ciani.giulia

9 comments posted 19yrs posted by ciani.giulia

Nand flash controller

Hi, all, Could anyone tell me whether there is a simple nand flash controller in the market so that I can interface it...

4 comments posted 19yrs

posted by cellterry

4 comments posted 19yrs posted by cellterry

PowerPC MPC5200B, changing mode to run in little endian

Hi, We are using Lite5200B eval board, out software is compiled using the Windriver diab 5.3.1.0 with the 5200B patch....

1 comments posted 19yrs

posted by taran.tripathi

1 comments posted 19yrs posted by taran.tripathi

I2C without resistors

Here you'll find a writing about a resistor-less I2C implementation: http://www.delajii.net/~mmihai/Articles/I2C_precha...

17 comments posted 19yrs

posted by iiahim

17 comments posted 19yrs posted by iiahim

How to display Fonts on the lcd

Hi I want to display various fonts on the LCD.Can you help me regarding this. LCD controller being used is ST7529 and wo...

1 comments posted 19yrs

posted by preethinandakumar

1 comments posted 19yrs posted by preethinandakumar

Zigbee device discovery

Dear All, I had doubts about the following topics 1)How a zigbee device recognises other zigbee devices within its rang...

0 comments posted 19yrs

posted by ramprasadpb1984

0 comments posted 19yrs posted by ramprasadpb1984

SD / MMC on AT91SAM7S256

Hello NG, i have the SAM7-P256 DEV-Board from Olimex. But if i open and compile the mmc demo - it doesn=B4t work. http:...

1 comments posted 19yrs

posted by peter.pippinger

1 comments posted 19yrs posted by peter.pippinger

Creating an interface to variables

Hi: I have an embedded system, platform: TI TMS320F2812 32-bit integer DSP. A module (.c file) contains external (to th...

6 comments posted 19yrs

posted by crcarleRemoveThis

6 comments posted 19yrs posted by crcarleRemoveThis