Embedded Programming

OK, Maybe the ADA folks are right

This compiles: ((adc_ping_pong) ? osc_vector : gyro_vector)[fill_vector][fill_ix] = raw_data; I have every confidence t...

9 comments posted 14yrs

posted by tim

9 comments posted 14yrs posted by tim

flash part equivalent to 27c240

Anyone know if there is a flash memory part equivalent to a 27c240 EPROM 256k by 16 bits. For use with a 68302 micro.

4 comments posted 14yrs

posted by darkknight.21

4 comments posted 14yrs posted by darkknight.21

Psychological Profiles When Applying for Software Development Jobs

I'm between jobs right now (and having contact with recruiters and applying for jobs). One employer, as part of their a...

14 comments posted 14yrs

posted by datesfat.chicks

14 comments posted 14yrs posted by datesfat.chicks

Setting carry on CF

Porting some code pieces written over the last two decades on a small CF part (mcf52211) and moaning. I often set or cl...

2 comments posted 14yrs

posted by dp

2 comments posted 14yrs posted by dp

Optimizing internet checksum on SH-4

Hello, I'm working with a 450-MHz SH-4 core. The architecture reminds me of the original Pentium in several ways, in th...

6 comments posted 14yrs

posted by root

6 comments posted 14yrs posted by root

Patent Reform Town Hall Meeting (Balt/Washington Area IEEE Consultants Network)

Co-sponsored by IEEE NCA Consultants Network, Baltimore Consultants Network, Society on Social Implications of Technolo...

97 comments posted 14yrs

posted by gnuarm

97 comments posted 14yrs posted by gnuarm

Anyone with milage on the TMS470R1B1, and IAR IDE for same?

Just starting to use the TMS470R1B1, which is a high-temp, high-rel processor with the ARM M3 core. At the customer's i...

10 comments posted 14yrs

posted by tim

10 comments posted 14yrs posted by tim

What Zigbee hardware to use?

Hello, Someone here with Zigbee experience could provide me some suggestions on what hardware (modules) to choose? I'm...

3 comments posted 14yrs

posted by mario.ribas

3 comments posted 14yrs posted by mario.ribas

Searching for 20 pin to 14 pin JTAG adapters.

Searching for a JTAG adapter to use a Segger J-Link (20 pin connector) on a Pandaboard (14 pin "TI" connector.) Found a...

8 comments posted 14yrs

posted by usenet

8 comments posted 14yrs posted by usenet

Inexpensive ARM JTAG Programmers

I'm looking for an inexpensive ARM JTAG programmer, to hand off to a customer to program flash on an LM3S2533. Currentl...

13 comments posted 14yrs

posted by tim

13 comments posted 14yrs posted by tim

What is the best way to asign power pins on connectors on mezzanine PCB ?

Hi, I am starting on designing a new mezzanine MCU module. The module will be about credit card size wih high density c...

2 comments posted 14yrs

posted by nobody

2 comments posted 14yrs posted by nobody

Snowball: interesting ARM board

FYI, While checking what ARM development boards are fashionable nowadays, I stumbled upon this: http://www.igloocommuni...

1 comments posted 14yrs

posted by usenet

1 comments posted 14yrs posted by usenet

Cross-compilation

I have a C application which I want to run in an embedded system. So I normally do my development on a PC, and then cro...

15 comments posted 14yrs

posted by chessmylitis

15 comments posted 14yrs posted by chessmylitis

CMOS camera interfacing

Hi, I've been wanting to start a project to build a small camera. I'm looking to take a cmos camera (most likely 1.3mp...

15 comments posted 14yrs

posted by handsonceheld

15 comments posted 14yrs posted by handsonceheld

one two three

one two three

5 comments posted 14yrs

posted by hamilton

5 comments posted 14yrs posted by hamilton