Hallo,
kaum macht man mal etwas ein paar Monate nicht, geht alles Wissen den
formatting link
und einen zweiten identischen aktuell nichtmal das Blink-Example flashen:
|1 [16/6456]mh@drop:~ $ /usr/lib/arduino/hardware/tools/avr/bin/avrdude -v -v -v -C/usr/lib/arduino/hardware/tools/avr/etc/avrdude.conf -v -patmega328p -carduino -P/dev/ttyUSB5 -b57600 -D -Uflash:w:/tmp/arduino_build_892829/Blink.ino.hex:i | |avrdude: Version 6.3-20190619 | Copyright (c) 2000-2005 Brian Dean,
formatting link
| Copyright (c) 2007-2014 Joerg Wunsch | | System wide configuration file is "/usr/lib/arduino/hardware/tools/avr/etc/avrdude.conf" | User configuration file is "/home/mh/.avrduderc" | User configuration file does not exist or is not a regular file, skipping | | Using Port : /dev/ttyUSB5 | Using Programmer : arduino | Overriding Baud Rate : 57600 |avrdude: Send: 0 [30] [20] |avrdude: Send: 0 [30] [20] |avrdude: Send: 0 [30] [20] |avrdude: Recv: . [84] |avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x84 |avrdude: Send: 0 [30] [20] |avrdude: Recv: . [fc] |avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0xfc |avrdude: Send: 0 [30] [20] |avrdude: Recv: . [94] |avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x94 |avrdude: Send: 0 [30] [20] |avrdude: Recv: D [44] |avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x44 |avrdude: Send: 0 [30] [20] |avrdude: Recv: . [04] |avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x04 |avrdude: Send: 0 [30] [20] |avrdude: Recv: . [fc] |avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0xfc |avrdude: Send: 0 [30] [20] |avrdude: Recv: . [84] |avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x84 |avrdude: Send: 0 [30] [20] |avrdude: Recv: D [44] |avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x44 |avrdude: Send: 0 [30] [20] |avrdude: Recv: . [04] |avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x04 |avrdude: Send: 0 [30] [20] |avrdude: Recv: D [44] |avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x44 | |avrdude done. Thank you.
Systemumgebung. Debian unstable, arduino IDE 1.8.9, nach den Problemen updated auf 1.8.12. Die Fehlermeldung ist bei beiden IDEs dieselbe und tritt auch auf, wenn man die avrdude-Kommandozeile aus der IDE
Board: Arduino Nano Processor: Atmega 328P old Bootloader (Atmega328P geht auch nicht) Serial Port: /dev/ttyUSB5 (das ist das Device Node, das beim Einstecken des Arduino erscheint).
Wenn ich Tools -> Serial Monitor aufrufe und den Resetknopf des
- richtiger Port? (dito)
- Anderen Arduino probiert? Ja.
- Andres Kabel probiert? Ja.
Ich bin mir doch so halbwegs sicher dass das auf diesem System schonmal funktoniert hat.
Hat noch jemand eine Idee?
Marc
-------------------------------------- !! No courtesy copies, please !! -----
Marc Haber | " Questions are the | Mailadresse im Header
Mannheim, Germany | Beginning of Wisdom " |
Nordisch by Nature | Lt. Worf, TNG "Rightful Heir" | Fon: *49 621 72739834