How bright would this be?

Put identical capacitors in series, and the capacitance of the series bank is the capacitance of one of them divided by the number of capacitors. If you have ten of these 5 pF capacitors, the total capacitance would be half a picofarad.

You want more than that. Stray capacitances of wires, etc. are easily a few picofarads.

The top of the "usual" small Van de Graaf generator available from a few scientific and educational equipment suppliers (for $200-$300 now I guess) is around 10-15 picofarads. That produces a spark that is easily visible, and a little bright - in good cases. At a voltage of 200 KV, this is 2-3 microcoulombs of charge.

These have stored energy low enough to be considered at least somewhat safe as toys.

Somewhat larger Van de Graaf generators in science museums have roughly

20 pF of capacitance and reach a voltage around 300 KV, which indicates 6 microcoulombs of charge. When discharging to a grounded sphere, sparks as short as 2 inches (150 KV between largish spheres, indicating about 3 microcoulombs) appear a little bright.

I know of one science museum taking precautions and requesting demonstration participants to cooperate with precautions against getting a full-force shock, although claiming that one should not die if shocked.

I have seen what a 150 pF capacitor charged to 10 KV does. This is 1.5 microcoulombs. It is a little bright.

To get 3 microcoulombs at 30 KV, the capacitors need to have a capacitance of 100 picofarads.

To get a really impressively bright spark, I would recommend 5-6 microcoulombs. This requires 166-200 picofarads for 30 KV capacitors.

I have seen what 100-200 microcoulombs does - that makes sparks that are very bright, almost or slightly able to put spots in your eyes. Assuming conductors involved have resistance no more than a few ohms, when the voltage is a few kilovolts.

In a Marx generator, the output spark may have brightness impaired by resistance of the sparks in the spark gaps between capacitors. You may need a little more for really nice bright sparks.

Now for shock hazard:

I have heard that shocks with 10 joules or more of energy can be fatal and shocks of lesser energy are unlikely to be fatal.

Please consider that whether or not electrocution occurs will depend on what point of your heartbeat cycle your heart is in, as well as random factors. Electrocution is so unreliable that "The Electric Chair" uses enough current to either cook vital organs or paralyze breathing muscles so that the condemned's brain gets deprived of oxygen or gets impaired by blood acidity from CO2 buildup in the blood. Lack of electrocution I expect to be similarly unreliable. My father ordered me to not store more than 1 joule in high voltage capacitors and high voltage capacitor banks when I was in my high-voltage spark-making younger days. I even remember one high-voltage-toymaking book titled "Electrostatics" advising to avoid getting shocked by more than 1/4 joule despite also saying that 10 joules is what it typically takes to have a major electrocution risk.

=============

Charge in coulombs is capacitance in farads times voltage in volts.

Energy in joules is 1/2 times capacitance in farads times square of voltage in volts.

Example: 100 picofarads at 150 KV:

Charge is 15 microcoulombs. This will make an impressively bright spark, and between sharp points or ends of thin wires could do so over a distance around 20 cm or 8 inches. Between large spheres this only sparks through about 5 cm or 2 inches, and presumably with significantly more light per centimeter if the resistance and inductance of the conductors in the circuit is low to achieve peak current in the kilo-amps.

Energy is 1.125 joules. It is easy enough to find sources indicating that this is safe to get shocked with, but I would not bet my life on it. I would get plenty of practice with quantities of stored energy less than

1/4 joule until I have gone a few months without getting zapped. And with deadly or possibly deadly amounts of stored energy, I would use all recommended cautions and avoid taking chances. Keep handy some plastic sticks and some discharging tools.

More shock hazard stuff:

1. A capacitor usually does not get completely shorted by a spark.

1. A capacitor that gets briefly completely shorted can have some charge afterwards. This phenomenon is called "dielectric absorption".

2. Non-fatal shocks can still be dangerous. If you get startled or suffer involuntary muscle contractions, you could bump something or bump into something - possibly breaking or zapping your project, possibly getting injured by falling or hitting something or getting stabbed by something, and possibly from touching or getting within spark range of a source of a lethal shock.

1. There is a bit of word out there that steady DC is the worst to get shocked by - NOT TRUE! AC and unsteady DC (including discharging high voltage capacitors with your body) are worse. Some horror stories of steady DC are out there because railroad workers lived to tell them after getting bigtime serious burns, including burning of internal tissues that take a long time to heal or never heal properly after getting cooked. I doubt you will cook any of your skeletal muscles from a Marx generator or a Van de Graaf or a neon sign transformer - the main worry here is shocking the heart into ventricular fibrillation.

- Don Klipstein ( snipped-for-privacy@misty.com)

cool.

neat.

30kV will ionise about 30mm of air so there's enough voltage there for a visible spark, how much current you get depends on the cyclic rate of the device - which depends on on your choice of charging resistors.

I don't know where you're going to get resistors rated to withstand 15kV pulses.

you can get about 30Kv from the high voltage circuit in a CRT based display, like a worn-out monitor... (dangerous though)

do you mean uA ?

I don't think less than 1mA has ever been fatal on the skin of a healthy person. if you limit the current the voltage will be restrained by the resustance of the load.

--

Bye.
   Jasen