1. Home
  2. Electronics Design
  3. 4-20mA transmitter and reciever

4-20mA transmitter and reciever

I'm having some problems specing out a data acquisition box that needs 4

4-20mA analong outputs and 4 4-20mA inputs. This is a custom box and so the circuit design will be at the IC level.

Questions.

Receiver:

1) should it always provide power for the loop (13 - 40VDC)? nominal 30 VDC. 2) Should it sense current on the positive output of the powersupply or the return (I've seen both ways)

Transmitter:

1) Always powered by the loop? 2) Common positive or ground? (or isolated)

The TX and RX are connected to a the same ground (all minus leads tied together) that is electrically floating with reference to earth.

The issue is that I've seen implementations that go either way for which side to sense and which current to control (positive draw with common return or return current with common positive).

Currently the transmitters are simple darlington tranny pairs with an emitter resistors and a opamp regulating the voltage drop across the resistor to match its input voltage. (textbook ckt) the ground side of all four emitter resistors is tied to the same board ground the input signal (quad DAC) is referenced to.

This works well for a system designed for this operation but fall on it a$$ if the positives are tied together and the current is sensed on the return lines (they all read the same due to current sharing).

The receiver is a simple 30V powersupply (referenced to board ground) with four 100 ohm resistors fanned off the positive and difference amplifiers measuring the drop from each one.

Again this does not work if the transmitters tie positives together and attempt to regulate the retuen current. (current sharing again)

What do you guys recommend?

Reply to
Mook Johnson
Loading thread data ...

On the last 4-20mA job I worked on everything was decided by the requirements of the PLCs. Their '4-20mA' input was no more than a burden resistor into a 5v ADC, all ADCs being ground-referenced.

It meant the all generated 4-20mA had to be positive output currents off the +24v rails, and everyone else's 4-20mA input amplifiers had to have the full common-mode voltage capability.

--
Tony Williams.
Reply to
Tony Williams

Depends on whether the field transmitter is two-wire or has a separate supply terminal. The receiver itself doesn't supply any power, you use an internal bus or external power supply.

Normally it senses the return if two-wire. Otherwise just tie positive to positive, negative is common for all signals.

Not necessarily but if you mean your own analog outputs they'll of course be internally powered.

Positive common, source.

Short answer: Make outputs sources (positive common) and inputs sinks (negative common).

You'll need to redesign the sources. No biggie but I'm too lazy to get off the chair and look up the exact circuit.

Reference them to ground and use 250 ohms.

By your description I'm not sure what you really are up to. Anyway, below are some standard instrument loop wirings.

...................... Internal power .+

30V-----------------o---------------+---------------------+ . o + | .+ ( ) [1] |

--------------+-----o---------------o - out o + | .Analog input 1 +--o( ) [2] - . | o - Internal | |etc o--------------------------------+ | circuitry | | .input 2 | - . | | . |

0V------------+-----o-------------------------------------+ ......................

............... [1] . - + o-----------------o( )o--+-----------------+ . input 1 + | | . +----+ o + . out o + ----- o-----------------o( ) [2] | | .input 2 + o - External | | . | power ----- . | supply o - ------o-------------------+----------------------+ . input common ............... [1] two-wire instrument [2] three-wire instrument

I won't bother drawing the current output, suffice it to say it's usually a source, the receiver goes between the output and the negative common.

- YD.

--
Remove HAT if replying by mail.
Reply to
YD

ElectronDepot website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.