Electronics Down Under

Re: Eternally confused Phil has a both way bet

On 9/1/05 12:03 PM, in article 43172666$0$524$ snipped-for-privacy@per-qv1-newsreader-01.i> Phil Allison the great unqu...

1 comments posted 20yrs

posted by ten

1 comments posted 20yrs posted by ten

What happened to my sound card?

My computer speakers died suddenly with a blown fuse. I assumed it was the speaker power supply so I replaced the speak...

4 comments posted 20yrs

posted by david

4 comments posted 20yrs posted by david

Want to Buy PC800 RDRAM

Hello fellow Enthusiasts and Techies, a friend of mine has a Compact Presario computer. One of the two sticks of 64MB P...

6 comments posted 20yrs

posted by john_c

6 comments posted 20yrs posted by john_c

High resolution, low cost, quadrature encoders

We can I source (I'm in Australia), high resolution (better than 10000 steps per revolution) quadrature encoders prefere...

11 comments posted 20yrs

posted by sandra

11 comments posted 20yrs posted by sandra

Docuprint C830 - Hardware error

Hi, I am using Docuprint C830 for a development project. When turned on the printer its tries to warm-up and gives the...

1 comments posted 20yrs

posted by peeyushnaidu

1 comments posted 20yrs posted by peeyushnaidu

TV repair website recommendation?

Hi all, Instead of throwing away a Sony Colour TV. I was wondering if there are any good websites on TV repairs. Thank y...

4 comments posted 20yrs

posted by doctor

4 comments posted 20yrs posted by doctor

Reading USB camera data from a microcontroller

Can some USB, microcontroller expert advise me how can a USB webcam be interfaced with a microcontroller (PIC, ATMega,...

8 comments posted 20yrs

posted by ivanNath

8 comments posted 20yrs posted by ivanNath

How to turn On/Off a +5vcc power?

I have a set of sensors and actuators all operating at +5v and draw 10mA to 680mA current. My microcontroller will stwi...

8 comments posted 20yrs

posted by jh14323

8 comments posted 20yrs posted by jh14323

dodgy mordaunt short speakers

My buddy and I have spent the afternoon generating horrible noises with a waveform generator and a NAD 216THX amplifier...

25 comments posted 20yrs

posted by my_name

25 comments posted 20yrs posted by my_name

GME TX-826 Schematic

Hi All, does anyone have a copy of a schematic for a GME Electrophone tx-826 uhf radio.I am wiling to pay for a copy. Ch...

1 comments posted 20yrs

posted by pussynuts

1 comments posted 20yrs posted by pussynuts

FS:Infocus LP-725 LCD projector (newcastle)

Hi have a LCD projector FS...which we have been using till recently (when the globe for it burnt out. The rest of the u...

5 comments posted 20yrs

posted by phmc

5 comments posted 20yrs posted by phmc

Connection marked as 'CA' on a fluorescent light

Hi Group, I have a fluorescent light which has a dimming transformer in it and a four pin plug. The usual 3 A,N,E and a...

11 comments posted 20yrs

posted by lbonnell

11 comments posted 20yrs posted by lbonnell

Freelance EE required

I am being a bit lazy here - I could go to the yellow pages I guess - but I thought I would give it a try here first. I...

0 comments posted 20yrs

posted by no

0 comments posted 20yrs posted by no

profile cutter

Hi I am looking for imformation or schematics for a MAGIC EYE PLASMA PROFILE CUTTER ,this is the type where you put a d...

0 comments posted 20yrs

posted by windy

0 comments posted 20yrs posted by windy

The stuff people throw out

We had our annaul council clean-up. Anyway a lot of "exchanging" or "thanx for that" goes on. There are even profession...

8 comments posted 20yrs

posted by associate

8 comments posted 20yrs posted by associate