Why does my Pip-Boy style display wash out completely when the battery gets low?

Nov 20, 2026 Last reply: 1 hour ago 5 Replies

First reply

Kit_Granite

I had the exact same symptom on a battery-powered display build, and in my case it wasn't the cell. Those little charge boards with the built-in boost converter, the ones that come in multipacks, have terrible regulation on the 5V side. They'll hold 5V with a fresh battery, but…

Read the full reply

So I've been building a Fallout themed weather station with an ESP32 and one of those 2 inch ST7789 screens, got the green monochrome look going and it reads the forecast fine. Problem is, when the LiPo drops below about half charge the whole screen gets noticeably dim and the colours look wrong, almost grey instead of that nice green. Plug it into USB and it snaps back to full brightness within a second. I assumed the boost converter would keep the voltage steady no matter what, that's kind of its whole job right? Is there something about these small charging modules where the output sags once the cell gets tired, or am I wiring something wrong? The display shares the same 3.3V rail as the microcontroller through a regulator, if that matters. Also wondering if I should just set the backlight PWM to drop when the battery voltage gets low, so at least it fades gracefully instead of looking broken. Has anyone else run into this with a battery powered TFT setup, or is my cell just old and tired? It's a cheap one from a multipack so I wouldn't be shocked if that's the answer.


I had the exact same symptom on a battery-powered display build, and in my case it wasn't the cell. Those little charge boards with the built-in boost converter, the ones that come in multipacks, have terrible regulation on the 5V side. They'll hold 5V with a fresh battery, but as the cell voltage drops the output slides down with it, and the moment the backlight pulls real current it dips even further. When you plug in USB the board just passes the cable's 5V straight through, which is why it snaps back instantly.

The reason the whole screen goes grey instead of just dimmer is that sagged 5V feeds the little regulator making your 3.3V rail. Those regulators need a bit of headroom above thier output to do their job, so once the input gets close to 4V the rail starts following it down. The ST7789 is fussy about that, brightness and colour both drift well before anything actually resets. The ESP32 doesn't care, it keeps running fine, so the only thing you notice is the display looking washed out. Easy way to confirm: put a multimeter on the 5V output while it's running off the battery and watch it as the charge drops. If you see it creeping from 5 down toward 4, that's your culprit. The fix that worked for me was swapping the boost section for a proper adjustable boost module set a little above 5V, giving the regulator the headroom it wants. Also worth adding a decent capacitor right across the display supply pins, those backlights cause short dips that drag the rail around.

As for the PWM idea, yes, do it regardless. Read the battery voltage through a resistor divider into an ADC pin and step the backlight down as it falls. It saves power, it hides any residual sag, and honestly a screen that dims as the power runs out fits the whole vault terminal aesthetic anyway.

The multipack cell might also be tired, but don't assume that first. Borrow a known good one for ten minutes and compare. If the voltage test shows the output holding steady with a fresh cell, your battery is fine and the converter is the problem.

Ran into the same greying-out on my ESP32 weather box and the culprit turned out to be thin wiring between the battery and the board. Swapped the flimsy dupont jumpers for short, chunkier leads and added a beefy electrolytic cap across the 3.3V rail right at the display, and the flicker stopped. Those multipack LiPos also tend to have weedy internal resistance, so a tired cell sags hard the moment the backlight kicks on. Mine was a no-name cell that tested fine on the meter but couldn't supply a burst to save its life. A proper brand cell fixed it.

Same thing happened on my garage sensor display and it drove me nuts for a week. Turned out my code was reading the battery fine but I had the backlight on full PWM the whole time, so any sag hit hardest right there. I ended up doing what you're suggesting, tied the backlight level to the ADC reading and stepped it down in a few chunks. Looks intentional now, kind of like the screen powering down in an old terminal. Also check your sleep settings, mine was waking every few seconds and hammering the cell.

Total beginner here so excuse the dumb question, but does the dimming happen faster if the wifi is on? Mine did somethig similar and it turned out the little radio bursts were pulling extra current at the exact moment the screen redrew. When I turned wifi off and let it update over usb only, the grey look basially went away. Might be worth testing with the radio off just to see if the sag gets better. Does yours connect to the network for the forecast, or is it all offline?

Update: swapped the flimsy jumpers for chunkier leads like the second reply suggested and added a cap across the rail at the screen, and the greying is way less obvious now, so some of it was wiring resistance all along. Still sagging on battery though. One thing, the wifi point got me thinking, mine updates every few minutes over the network. coud those radio bursts be enugh to pull the rail down mid redraw even with a half full cell?

Join the Discussion

Have something to add? Share your thoughts — no account required.

Didn't find your answer?

Ask the community — no account required