RPi desktop on a Aer Aspire TC-780 - amy gotya's ?
Nov 20, 2026 Last reply: 1 hour ago 16 Replies
First reply
Andy Burns
Sounds like a 'hybrid' SSHD device, will just show as a 1TB sata device, with the 128GB acting as a 'hidden' cache. I've never installed PiOS on a non-Pi device, but yeah I'd expect write to thumbdrive like any other bootable OS media.
Recently I got an old Acer Aspire TC-780 (Win10), and, as I already got some RPi's, I thought of putting "Raspberry Pi Desktop" on it (
formatting link
, at the bottom).
The TC-780 comes with, if I interpret the specs correctly, a combined HDD+SSD (1TB, 128GB).
I take it I just put the downloaded ISO onto a thumbdrive, plug it into the 'puter, boot from it and than follow the instructions to install the new OS.
My question is : are there any gotya's I should be aware of ? A specific BIOS configuration perhaps ? Anything else I should be aware of ?
Regards, Rudy Wieser
Didn't find your answer? Ask the community — no account required.
Hi, Iam looking for smd chip marked u2 on acer aspire 1310 main boardbecause USB...
A
Andy Burns
Sounds like a 'hybrid' SSHD device, will just show as a 1TB sata device, with the 128GB acting as a 'hidden' cache.
I've never installed PiOS on a non-Pi device, but yeah I'd expect write to thumbdrive like any other bootable OS media.
T
Tim Albers
Am 20.11.2026 um 10:41 schrieb Andy Burns:
Nope, it's a desktop PC with a small SATA SSD for the OS and a regular magnetic HDD for storage.
R
R.Wieser
Andy,
Yep. I've been looking for a second drive - or even something special on the motherboard - but did only find a single drive.
That's possible. Though the BIOS showed one to be connected to SATA1 and the other to SATA2.
IOW, its quite possible that both will be visible from another OS than Win10.
... and as I'm going to install a Linux version ...
I guess I will find out soon enough. :-)
Regards, Rudy Wieser
R
R.Wieser
Tim,
I think Andy is right in regard to the "hybrid SSHD device". Other than the CD/DVD drive there seems to be only a single other device connected to a SATA connector. I've also looked if there was perhaps a SSD module on the motherboard itself, but could not find anything.
I'm not so sure that the SSD part will be a hidden chache though. The BIOS shows them (HDD, SSD) seperatily, so I'm assuming that I (read: Linux) can access them seperatily.
But... No known gotya's ?
Regards, Rudy Wieser
P
Paul
You could boot into Win10, and use Disk Management (right-click Start and it is in the menu), and you can look at the disk configuration and orient yourself with respect to what the two devices are doing right now. Like the 1TB drive could have a single partition saying "Data" and the 128GB SSD could have a partition that ways "Windows".
You know how to poke around in there, and figure out the disk layout.
Then you can decide, what OS you want to install, and where is the best place to install it.
Someone may have swapped used storage devices in place of the original ones. In Win10, I would use something like "CrystalDiskInfo9_5_0.zip" to check the SMART data on the SSD and determine what percentage of life is left on the drive. It's unlikely to be totally worn out, but you should be checking the brand and model, because some older ones are a real liability as storage (the first generation had some "drop dead" SSDs that caused grief). It took a while for the industry to learn how to write firmware for SSD drives. Intel staff, when they entered the SSD business, they took one look at the code the other companies were using, and they did an eye-roll, the code was so bad.
If *anything* in that box needs to be replaced, or if an item was removed by the refurbisher to cheapen the item, these days the replacement cost of just about any item inside that PC, is going to cost you more than the entire purchase price of the refurb. Now, more than ever, you're depending on the refurbisher company to be an honest one.
Paul
R
R.Wieser
Paul,
I can boot into Win10 alright, but than I'm shown a user-login screen. Which I can't pass (?). So, no access to Disk Management either (?).
(in case you are unaware, I'm not a Win10 user. Other than *very* superficially I have no idea how it works)
Thats one of the gotya's I was thinking of : I'm accustomed to Windows installations where I can delete and create partitions as part of the installation process, but I've got no idea if Linux offers the same.
As the the 'puter - and its drive - has survived its previous user(s) I'm going to assume it will survive me too. :-)
But in the case that the SSD would crash but the HDD still would function I could just re-install the whole thing on that. And if it totally crashes than I've got a few spare SATA drives laying about.
No refurbisher involved. Someone put it outside as trash, and I decided to take a chance. The thing looks complete - no dangling wires.
Regards, Rudy Wieser
J
John R Walliker
Maybe, but then they did something even worse by locking the drive when the specified number of writes had been reached, even if the drive was actually fine. Many drives (certainly some Samsung ones) have far better write endurance than their specification suggests.
T
Theo
It's supposed to be at the very front of the mobo - see number 9 here:
formatting link
A 'hybrid' drive wouldn't show up separately, but this appears to be a separate M.2 stick - probably SATA M.2 if it shows up as a SATA disc.
I'll be limited to SATA speeds (about 550MB/s) but still quicker than the HDD.
I'd install RPi OS on the 128GB drive and then you can mount the HDD for user data later. 128GB should be plenty for installing apps and other system stuff.
Theo
R
R.Wieser
Theo,
It turns out you're right.
After I disconnected the HDD and still saw the SSD in the BIOS I took a better look at the location you mentioned, and saw the SSD module - laying flat on the motherboard and the of same color (which is why I overlooked it : I expected a big module, like the RAM ones, sticking up from the motherboard).
An closer look showed that the SSD module is in a socket, and not soldered directly onto the motherboard. If it fails it can be replaced (or removed).
Inclusive the swap partition ? I assumed that the HDD would be a better place for it.
:-) As an RPi can run on a 4GB micro-SD I must assume that 128GB is way, way, waaaay more than plenty for it.
Still no gotya's. Must be my lucky day.
Regards, Rudy Wieser
T
Theo
Swap wants to be as fast as possible, so SSD is better for that. There's a small impact of extra wear on the SSD, but unless you're thrashing swap all day every day it's unlikely to be an issue. If you keep some amount like
10% of the SSD zeroed then the controller can use those blocks to improve the wear lifetime ('over provisioning').
Swap can also be used for hibernate, so it's useful to have at least as much as the physical RAM you have (although it's possible to also use a hibernate file).
Indeed :)
Theo
R
R.Wieser
Theo,
Do you mean unpartitioned, or would something special (zeroed?) be needed ?
And thanks for the suggestion.
Regards, Rudy Wieser
T
The Natural Philosopher
I've been using swap on SSD on this machine for several years. No issues at all
I think one key thing is use a much bugger drive than you (think you) need. I have 250GB here and use about 130GB
T
Theo
'Empty'. When you delete a file, typically filesystems tell the device that the blocks are no longer used (this is called 'TRIM') and it can put them back into the empty block pool. The more empty blocks there are, the more breathing space the SSD has to use when parts of the flash wear out.
If you zero blocks, the SSD can also decide they're 'empty'. If you leave parts unpartitioned but still containing data from the last time it was used, the SSD is still contractually obliged to keep the data in case you need it another time and so it can't reallocate them to cover wear.
Just making a big file and then deleting it is usually enough to trigger TRIM of the blocks, but also zeroing the SSD and then leaving 10% (or whatever) unpartitioned works too.
This can also help with 'performance consistency': if you want to write but the SSD has to do a lot of juggling to find an empty block, maybe erasing and shuffling some other blocks, then you can get erratic performance under heavy load. But that's only really an issue with big write workloads like database servers, not domestic desktop use.
Theo
R
R.Wieser
Theo,
Ah, you mean I should never fully use the whole partition ("Used space" vs "Free space"). With 128GB to work with I'm not going to worry about that. :-)
I don't understand : when a block is not part of any file chain than its unused. The wear-leveling process could commandeer such blocks at any time - even though that could twart a later "undelete" attempt.
Hmmm ... Does Linux even have an "undelete" method ?
Also, files can contain lots of zeroes. How will the wear-leveling mechanism know that such in-use blocks filled with zeroes should not be taken ?
That doesn't make any sense. The data in blocks not part of any partition (or file!) needs to be kept ? For what reason ?
Again, I do not understand. The blocks in the unpartitioned area might be zeroed out, but the moment the wear-leveling mechanism swaps such a block out with one inside a partition that swapped-out block now in the unpartitioned area is going to contain data.
Regards, Rudy Wieser
R
Richard Kettlewell
Off by default in ext4, I believe.
The drive doesn’t know which (logical) blocks are not part of a file, unless the OS tells it.
P
Paul
A technical challenge then :-)
OK, now I see why you're in a paving mood.
One problem is, there were some nice (reasonably easy) hacks to become Administrator while booting.
There was the OSK hack (replace OnScreenKeyboard executable with cmd.exe) and one other file could be abused in a similar manner, and when that Command Prompt opens, it happens to be Administrator. You can then enable the Real Administrator account (and set a password for it).
Once the hack is executed, the next time you boot, the challenge page lists multiple accounts in the lower left corner, you select "Administrator", enter that fresh password, and... you're in. I helped someone remotely to do this once, he succeeded, but it was like pulling teeth and took a fairly long thread before he was in.
A couple of those holes were closed by later patches to Windows. As far as I know, there is one hack left that was not patched. There used to be a web page that tracked the hacks (it doesn't tell you which ones are blocked, it just describes the palette of hacks available to you).
An example of some terminology...
formatting link
But it does not work because the utilman.exe (or osk.exe or sethc.exe) does not exist!
I believe one of the tricks, was to start in Safe Mode, Windows Defender is not loaded then, and then the hack works again. But even getting Safe Mode to work, is a bitch (it's not like the old days where hammering on F8 always worked). You need to boot installer media, select Troubleshooting instead of Install, use the Command Prompt, and add Safe Boot to the menu. From my notes:
F8 boot menu for Windows 10:
dir /AH C:\boot\BCD # verify The BCD file is there. # It is a registry hive and is binary inside # You cannot edit the BCD, unless you know where it is.
That gives an F8 menu, you Safe Boot, then pretend to be using the On Screen Keyboard to enter the password (as if you had a touch screen), and instead of osk.exe executing, your copy of cmd.exe executes instead and you become administrator. And from there, enable the Real Administrator account and now you have elevated yourself in.
net user administrator /active:yes # Turn on the disabled Administrator account
net user Administrator 12345 # Set a password for the Real Administrator account
There is no need of Administrator being activated. You don't leave it turned on. As long as a newuser you create belongs to the Administrator group, that's like "sudo" in Linux. The UAC prompt signals a "sudo attempt" in Windows. So once an account you own belongs to Administrator group, you can set that active:no again.
Anyway, I know you have no interest in stuff like this, so pave away.
If you boot a Linux Mint for example, you can use "gnome-disks" to review the partitions using a graphical view similar to Disk Management. There is also gparted, sudo gparted, and you can select one of the devices and review the partition set. You could even do a part of the hack to get back in from there, but the