Embedded Programming

Serial port monitor

Hi! I am trying to capture RS-232 communication from my PC to a target board. The PC sends a command and the target boa...

10 comments posted 22yrs

posted by mshemanth

10 comments posted 22yrs posted by mshemanth

A very interesting embedded application

I think this is not the first, or even second time uCs have been put in shoes. This is definitely the coolest applicatio...

1 comments posted 22yrs

posted by larwe

1 comments posted 22yrs posted by larwe

Terms in automotive electronics

Hello World, I am trying to make a device to measure the fuel level in a scooter. It is fitted with a fuel level sensor...

6 comments posted 22yrs

posted by nntpuser

6 comments posted 22yrs posted by nntpuser

Embedded JPEG compression

I have looked for some time at the Independent JPEG Group set of files for JPEG compression. These are extremely diffic...

6 comments posted 22yrs

posted by fred

6 comments posted 22yrs posted by fred

atmega8 as twi-slave

hi, i try to use the atmega8 as a slave-device on the twi (i2c) bus. i can send the slave-adress and the atmel reacts o...

1 comments posted 22yrs

posted by ojoa

1 comments posted 22yrs posted by ojoa

Basic c question from a newbie

Hi all, I am new to embedded field and I found following function prototype.I am not getting why the parameter is decla...

13 comments posted 22yrs

posted by vashwath

13 comments posted 22yrs posted by vashwath

AT91 Library for ARM920T?

I did some work with the eb40a ARM7 devkit last year, using GCC for cygwin (http://www.macraigor.com/full_gnu.htm) and...

0 comments posted 22yrs

posted by magnus

0 comments posted 22yrs posted by magnus

want helping in acessing memory mapped registers in Elansc520

hi all, i want help in how to access the memory mapped registers of the can controller, through programming the PAR reg...

2 comments posted 22yrs

posted by banu1118

2 comments posted 22yrs posted by banu1118

help needed PID control calculations(BRUSHLESS DC MOTOR CONTROL)

Hi ALL, I am mohd sulaiman. I am working on Brushless dc Motor position control.In my application we are controlling th...

4 comments posted 22yrs

posted by sulaimanmohammed

4 comments posted 22yrs posted by sulaimanmohammed

Low cost SBC with IDE interface

Hello, I am looking for a small SBC that includes serial, Ethernet, and an IDE interface for connection to a CompactFla...

2 comments posted 22yrs

posted by jfathman

2 comments posted 22yrs posted by jfathman

low cost LCD for embedded products

Hi, I apologize for this commercial posting, but some designers can be interested in. We have some original Nokia LCD 3...

0 comments posted 22yrs

posted by laurent.gauch

0 comments posted 22yrs posted by laurent.gauch

reset cristal CS8900A

Does anyone know how can I reset the CS8900A by software? I'm using that micro in 8 bit mode and I need to reset it whe...

2 comments posted 22yrs

posted by fedeh

2 comments posted 22yrs posted by fedeh

Mouse not showing

I have a ICOP embedded 386 board with windows 95 loaded, the board dose not pick up the mouse. Thanks Mike

1 comments posted 22yrs

posted by mike

1 comments posted 22yrs posted by mike

8051 with CAN and Flash

Hi! I am desperately looking for a 8051 microcontroller with CAN onboard and Flash ROM. If anybody knows about one pleas...

3 comments posted 22yrs

posted by news

3 comments posted 22yrs posted by news

Graphic voting systems

This morning I heard on the radio of the problems with these electronic voting systems. As an embedded systems develope...

34 comments posted 22yrs

posted by hamilton

34 comments posted 22yrs posted by hamilton