Embedded Programming

Using software breakpoints with RealView debugger

We had a problem of setting software breakpoints in RVD. The solution we found is this: All you have to do is to set tw...

0 comments posted 21yrs

posted by avimanor

0 comments posted 21yrs posted by avimanor

standalone programmer for PIC?

Hi Folks I have been looking into some sorts of portable standalone programmers for PIC. The idea is for on site firmwa...

18 comments posted 21yrs

posted by calvin_chan

18 comments posted 21yrs posted by calvin_chan

MicroChip PIC 16C63A migration path?

We use the 16C63A a lot, does anyone have a simple answer to what the next chip after this one would be? I would like t...

7 comments posted 21yrs

posted by a.marchini

7 comments posted 21yrs posted by a.marchini

GNUARM tool update at www.gnuarm.com

Pablo has updated the gnuarm tools which are availble at www.gnuarm.com The site includes sources and binary distributi...

3 comments posted 21yrs

posted by spamgoeshere4

3 comments posted 21yrs posted by spamgoeshere4

Motorola MCORE

I have some questions about the Motorola MCORE processor, but I'm not sure if this is the correct group to ask this que...

1 comments posted 21yrs

posted by pj2k4

1 comments posted 21yrs posted by pj2k4

Code for PS/2 mouse for DS80C400

Whilst I can still get serial mice I feel their days are numbered moreso than PS/2 mice which presumable will also even...

5 comments posted 21yrs

posted by Fred

5 comments posted 21yrs posted by Fred

help required on SC28C94 Data Transmission

Hi, we are working with SC28C94 for data communication. this IC(SC28C94) we are using in polling mode not in interrupt...

1 comments posted 21yrs

posted by podduturiniranjan

1 comments posted 21yrs posted by podduturiniranjan

WIZ-C HELP???

Hi, im currently using Wiz-C and have used the application designer to > develop the software for my PIC. Everything lo...

1 comments posted 21yrs

posted by scottnn

1 comments posted 21yrs posted by scottnn

MC68360 HDLC/SDLC.

Sorry if the questions sound silly, but I'm a newbie . . . I need to develop the SDLC protocol for the MC68360. I read...

1 comments posted 21yrs

posted by cristian291

1 comments posted 21yrs posted by cristian291

GNU Power PC tools?

I am looking for a pre-built set of PowerPC tools that support the IBM/AMCC 440 series. Scott

2 comments posted 21yrs

posted by scott

2 comments posted 21yrs posted by scott

Could PIC handle this?

Could a PIC handle interfacing via rs232 with a GPS unit, and comparing the location against a list of ~5000 stored pos...

35 comments posted 21yrs

posted by dapage

35 comments posted 21yrs posted by dapage

Re: problems with ARM-ELF toolchain under Cygwin

Hi Jens, I am getting the same assembler error when using ARM GNU tools (Rev: 2.95.3-1). arm-unknown-elf-gcc -c src\tes...

5 comments posted 21yrs

posted by jwalinp

5 comments posted 21yrs posted by jwalinp

Compact Flash I/O firmware design

I am about to develop a Compact Flash I/O device for PDA (DELL AXIM). Fortunately I found a CF interface chipset with a...

1 comments posted 21yrs

posted by gpsabove

1 comments posted 21yrs posted by gpsabove

JTAG TAP

Hi, I am writing a bit of software to control a JTAG port, but I am having a bit of trouble getting it working. Below a...

5 comments posted 21yrs

posted by pault_rem_.ngea

5 comments posted 21yrs posted by pault_rem_.ngea

Free ARM Compilers?

I have found 2 GCC ports for ARM. Any experience or opinions on which is best? Here are links to both. http://gnuarm.com...

16 comments posted 21yrs

posted by tcarley

16 comments posted 21yrs posted by tcarley