Embedded Programming

Flow-charting software?

Opinions about flow charting software??? I have tried flow chart software in the past, but it wasn't very easy to use. A...

16 comments posted 20yrs

posted by scottk

16 comments posted 20yrs posted by scottk

Quick question, how do I supply +-5V?

I have a large board which asks for three power supplies, +3V, +3.3V and +-5V. First two can be easily satisfied with t...

28 comments posted 20yrs

posted by Francis.invalid

28 comments posted 20yrs posted by Francis.invalid

M16C Security

I want to add security to an M16C project. The manual in Figure 1.30.2 shows the 7 security bytes ID1 thru ID7 on the l...

4 comments posted 20yrs

posted by ron

4 comments posted 20yrs posted by ron

TDA7513T

Hi, From the ST website I read about TDA7513T. It looks amazing but I can't find it anywhere. Nobody is selling it. I w...

4 comments posted 20yrs

posted by tberisha

4 comments posted 20yrs posted by tberisha

Open challange target

Dear Friends...... Really new Idea with new challange, If anybody can design a device or system which putting next to T...

14 comments posted 20yrs

posted by bhimanipankaj

14 comments posted 20yrs posted by bhimanipankaj

QRY regarding IOP80331

Hi, Not sure if this is off topic :) but Im trying to use the GF(Q) multiplication in the AAU for 80331.What is happeni...

0 comments posted 20yrs

posted by amritanshu

0 comments posted 20yrs posted by amritanshu

Ever 'souped up' the ADC on Renesas uC?

Hello All, Can anyone share their experience on pushing the envelope of the 10bit ADC on Renesas micro controllers? The...

22 comments posted 20yrs

posted by notthisjoergsch

22 comments posted 20yrs posted by notthisjoergsch

AT91RM9200/Davicom and Altima phy compability

Hello, We're having two ethernet problems with an Atmel AT91RM9200 CPU based construction. I'm interested if we are the...

0 comments posted 20yrs

posted by e4borgen

0 comments posted 20yrs posted by e4borgen

effect of context switch time on scheduling

Not sure if this question concerns this group .. Writing a small application which creates schedules based on the ( Lea...

0 comments posted 20yrs

posted by viveklinux

0 comments posted 20yrs posted by viveklinux

PCIe for Host to Host

Is there any way to use PCIe to do host to host communication? I'm looking at ASI, how it was built with means of encap...

0 comments posted 20yrs

posted by rektide

0 comments posted 20yrs posted by rektide

Future of Microchip Development Tools? See inside...

http://Microcontroller.com/Embedded.asp?did=142 Atmel; Moto... uh, Freescale(!); 8051; ARM; Microchip. I'm taking a sho...

7 comments posted 20yrs

posted by editor

7 comments posted 20yrs posted by editor

Question: Suggestion on good PIC programmer from $50..$300

Hi, I am new to this. I am looking for a cheap pic programmer ( as cheap as it can get ) with following. 1) Program a P...

2 comments posted 20yrs

posted by kamal.verma

2 comments posted 20yrs posted by kamal.verma

HC08 monitor mode, security problem

Hi, I would like to program FLASH memory of a HC908AZ60 controller via the monitor function of the controller. Reading/...

8 comments posted 20yrs

posted by roy.rutten.remove.this

8 comments posted 20yrs posted by roy.rutten.remove.this

ADPCM Coder/Decoder

Hi, I need some technical information. I would like to know if you can supply us a software that can make a ADPCM or LP...

2 comments posted 20yrs

posted by famin75

2 comments posted 20yrs posted by famin75

Getting trigger signal to application

Hi. We need to get a hardware trigger signal (TTL level) into a linux box, delivered to an application. That applicatio...

1 comments posted 20yrs

posted by please

1 comments posted 20yrs posted by please