Embedded Programming

AVR JTAG programmer choice

My JTAG Cable1 has just failed and I need to get another JTAG programmer, ideally with a USB interface although if it h...

16 comments posted 20yrs

posted by enquiries

16 comments posted 20yrs posted by enquiries

Mask Registers in CAN

hi all, Here in my CAN project i am using the Fujitsu controller (MB90F420).That has the two acceptance mask registers(...

1 comments posted 20yrs

posted by mrpanchu2003

1 comments posted 20yrs posted by mrpanchu2003

seeking dev board with eth/wifi/serial

I'm looking for a development board to run a fairly simple bit of logic between a number of interfaces (10/100 Ethernet...

9 comments posted 20yrs

posted by LBJames

9 comments posted 20yrs posted by LBJames

JTAG and flash

I'm new to learning about jtag and it's capabilities, and my professor isn't helping me at all. I understand jtag is ma...

19 comments posted 20yrs

posted by ixqnxjpumxklao

19 comments posted 20yrs posted by ixqnxjpumxklao

Re: dynamic memory allocation

> True statement, but how do I determine this bound? > > >> > > >> > >> > >>Hi there, > >> > >>I'm experimenting with d...

6 comments posted 20yrs

posted by wkaras

6 comments posted 20yrs posted by wkaras

VU meters on LCD

I am having difficulty displaying nice VU meter on a character display, right now I have allowed for 8 segments per cha...

8 comments posted 20yrs

posted by rsloan2003

8 comments posted 20yrs posted by rsloan2003

AC Motor Reference Kits

From International Rectifier exist two Reference Kits for Motor design. IRADK31 use 2A 500V Mosfets and a PIC Controlle...

2 comments posted 20yrs

posted by janvi

2 comments posted 20yrs posted by janvi

Blackfin exceeded SCLK abs max / Damage possible?

Hi Everyone- My Blackfin ADSP-BF532 seems to have been damaged. The data sheet says abs max for SCLK is 133MHz. I accid...

0 comments posted 20yrs

posted by johnspeth

0 comments posted 20yrs posted by johnspeth

CFP: 2006 MAPLD International Conference

First Call for Papers 2006 MAPLD International Conference Ronald Reagan Building and International Trade Center with a...

0 comments posted 20yrs

posted by richard.b.katz

0 comments posted 20yrs posted by richard.b.katz

Re: Node Status in CAN Communication

Ins CSR register [Bit 10] NT: Node status transition flag If the node status is changed to increment, or from Bus Off t...

0 comments posted 20yrs

posted by no.valid.eml.add

0 comments posted 20yrs posted by no.valid.eml.add

RS-485 Troubleshooting

Hi, I am using Rabbit development board which has separate ports for RS232 and Rs485. Right now i am using a single por...

15 comments posted 20yrs

posted by rahuls

15 comments posted 20yrs posted by rahuls

Controller Area Network Simulator

hi there, is there any demo version Simulator(for Controller Area Network) available on the web. because i want to run...

0 comments posted 20yrs

posted by mrpanchu2003

0 comments posted 20yrs posted by mrpanchu2003

Re: microcontroller selection

> Hi, I want to select a 8 bit microcontroller which can be run under 3V > and with 12MHz clock. Any choice? > Strange...

3 comments posted 20yrs

posted by alfkatz

3 comments posted 20yrs posted by alfkatz

Re: Xicor X28HC256 EEPROM

> Hi, > > can anybody tell me where to find more internal information about the > Xicor X28HC256 EEPROM than in the nor...

1 comments posted 20yrs

posted by ryan weihl

1 comments posted 20yrs posted by ryan weihl

HE-104 AC p/s

Hi, I'm building a pc/104 PC as a side project for fun. I purchased a pc/104 board as well as the he-104 12v vehicle po...

2 comments posted 20yrs

posted by kevincw01

2 comments posted 20yrs posted by kevincw01