Embedded Programming

  1. Home
  2. Embedded Programming
16390 Threads Posts
to

Worth reading in Embedded Programming

eCos - synthetic linux target

Is anybody familiar with building eCos applications for the linux = synthetic target? --=20 Karsten P. Hoffmann 3M Deut...
2 comments posted 19yrs
posted by karsten.p.hofffmann
2 comments posted 19yrs posted by karsten.p.hofffmann

cache problem

hi: In my v2pro embedded system, i use an off-chip sdram(not ddr) to plac my code. but now i find that i can only write
0 comments posted 19yrs
posted by qingfeng051206
0 comments posted 19yrs posted by qingfeng051206

stuart interrupt problem on pxa255 board

Hi, i'm developing a bootloader on a pxa255 based board. I have a problem using stuart RX interrupt. When I enter a cha...
0 comments posted 19yrs
posted by tsc.lee
0 comments posted 19yrs posted by tsc.lee

Profibus Master simulator

Dear friends, I am working on implementation of profibus slave for one of our products.To test the implementation ; I a...
8 comments posted 19yrs
posted by nitin.nimbalkar
8 comments posted 19yrs posted by nitin.nimbalkar

Need a SD (memory card) controller chip.

Hi All, I need a SD memory card controller chip, I also need to porting some MCU code, and need UART interface, low spee...
17 comments posted 19yrs
posted by bokiteam
17 comments posted 19yrs posted by bokiteam

MPC5xx OS?

Excuse my ultra-ridiculous query (if it is ridiculous) Off late, I was introduced to MPC555 based systems and we progra...
5 comments posted 19yrs
posted by culdesacked
5 comments posted 19yrs posted by culdesacked

Watchdog msp430

Hi, I have an MSP430 and set the watchdog timer, however, when I cut power off and return power, sometimes it'll reset,...
5 comments posted 19yrs
posted by ddshore
5 comments posted 19yrs posted by ddshore

Hightec TriCore toolchain sources (again)

Hello, I would be very grateful if someone having recent sources of their toolchain would share them... Hightec-rt.com...
3 comments posted 19yrs
posted by bfroemel
3 comments posted 19yrs posted by bfroemel

Data acquisition syncronization by using timestamp

Hello all, I need to get some helps on timestamp generation circuitry in a data acquisition system. Each aquired data w...
14 comments posted 19yrs
posted by yanwain
14 comments posted 19yrs posted by yanwain

EZ-USB FX2 Firmware

If anyone has an endpoint 2 or 6 configured for autoin in slave mode could they please send me some code how exactly the...
1 comments posted 19yrs
posted by lloyd.rochester
1 comments posted 19yrs posted by lloyd.rochester

Coldfire 5474 and GMP

I'm having some problems building gmp on the EVBLite board. Apparently, there is no support in GMP for the Coldfire red...
0 comments posted 19yrs
posted by spammersarevermin
0 comments posted 19yrs posted by spammersarevermin

Message Compatibility

Hello, Please let me know if I send the message supported by a CAN network node to the FlexRay supported network then wo...
0 comments posted 19yrs
posted by itzadi99
0 comments posted 19yrs posted by itzadi99

Porting uClinux on MCF5282

Hi I Have an MCF5282 ( ColdFIre ) Evaluation Board. Now I want to go about Porting uClinux on this. Can someone point m...
1 comments posted 19yrs
posted by techie.embedded
1 comments posted 19yrs posted by techie.embedded

EZUSB FX2LP transfer speed

Hi out there, I still try to speed up my little curcuit that contains a CY68013A FX2LP Chip. I am able to transfer 3,5...
6 comments posted 19yrs
posted by mail
6 comments posted 19yrs posted by mail