Embedded Programming

Freescale Introduces LOW power 56F8000

http://www.microcontroller.com/news/Freescale_MC56F8006.asp Standby currents of less than 1uA. Draws 50uA @ 32MHz. Thes...

4 comments posted 17yrs

posted by contact01

4 comments posted 17yrs posted by contact01

Fastest Processor Under 1W?

Hello All, I'm evaluating some embedded processor options and was wondering what the best options are with a 1W power l...

22 comments posted 17yrs

posted by kmaryan

22 comments posted 17yrs posted by kmaryan

TCP packets : end of thre-way handshake and start of data-transmission - how to detect ?

Hello All, I'm (still) busy trying to write TCP/IP for an rtl8019as NIC connected to an ATMega32 controller, and seem t...

28 comments posted 17yrs

posted by address

28 comments posted 17yrs posted by address

0x07 or 0xE0 CRC

Hi, I find that the polynomial for CRC-8-ATM is 1 + x + x^2 + x^8 and the representations as 0x07 or 0xE0 in the below...

7 comments posted 17yrs

posted by karthikbalaguru79

7 comments posted 17yrs posted by karthikbalaguru79

High-speed signals crossing a split-ground

Hi, I'm working a design that has isolation between two sub-systems on one PCB (the grounds are separate). One side is...

14 comments posted 17yrs

posted by xjjzdv402

14 comments posted 17yrs posted by xjjzdv402

OT - Project/Task/ToDoList tracking?

Is anyone using a project/task/ToDoList tracking system that they like? I'm looking for a new/better way to track proje...

4 comments posted 17yrs

posted by scott

4 comments posted 17yrs posted by scott

Need help to start with USB

I need to read/write sectors on USB flash memory mass storage. (I hope this is the correct title) AFAIK, this has two r...

12 comments posted 17yrs

posted by aleksaZR

12 comments posted 17yrs posted by aleksaZR

Linker Script Question

For the sample linker script below I have two questions.... 1) How can I make sure the image between the end of output1...

3 comments posted 17yrs

posted by AlfieNoakes

3 comments posted 17yrs posted by AlfieNoakes

I need to write a command protocol divided in 3 layers

Hello I need to write a command protocol divided in 3 layers. A data link layer, a network layer and an upper layer. I'...

14 comments posted 17yrs

posted by billy

14 comments posted 17yrs posted by billy

Decent debugger for linux on embedded devices

I have been spoilt using MS Visual Studio for the last few years. Now I am back to using gdb and ftp'ing to the target....

6 comments posted 17yrs

posted by therealandy

6 comments posted 17yrs posted by therealandy

AT91SAM7 USART

I have an issue with the baud rate clock on a AT91SAM7S processor. The processor will run from an external 18.432MHz cr...

0 comments posted 17yrs

posted by sjones

0 comments posted 17yrs posted by sjones

nibz embedded example under construction ideas wanted

Hi http://code.google.com/p/nibz/wiki/ReferenceSystem has been started in earnest. The idea to split the UFM on MAX II...

3 comments posted 17yrs

posted by jackokring

3 comments posted 17yrs posted by jackokring

TMDS to LVDS

Hi folks, I need to convert TMDS to LVDS. Im sure someone has done this before, so rather than reinvent the wheel, I'd...

3 comments posted 17yrs

posted by ian

3 comments posted 17yrs posted by ian

Spec2000 benchmarks : runtime with Simplescalar

Hi, I want to run few Spec2000 benchmarks on simplescalar but I do not know how much simulation time these benchmarks t...

0 comments posted 17yrs

posted by aaruljain

0 comments posted 17yrs posted by aaruljain

Seeking comparisson of free RTOS for embedded

Sorry if this is a FAQ, I have googled around and don''t find much. What to I want from an RTOS? - The standard message...

4 comments posted 17yrs

posted by Papa.Legba.666

4 comments posted 17yrs posted by Papa.Legba.666