I have the following items. Please bare with me being I have found verylimited info. on these. I am assuming that if you are looking at this postthen you are familiar with test jigs. Anyhow I have the following: Sharp Jig- QPWBF2382TAZZ w/ QPWBN2381TAZZ attached to it. I could notfind anything out about this item. It has 8 slide switches and one pushbutton switch. From Left--Right Top--bottom they are labeled as follows:Sensor, Error Display, Manual SW-P Adj, (push button) Auto SW-P Adj.,(bottom) VCR Adj, Low Bat, A-Track, Adj Mode, RE Test. There are alsovarious test pin clips on the right hand side which are labeled: H-Amp-SW,H-SW-P, 16.5V, EE Lev, W/D, PB FM Sharp Jig- QPWBF2450TAZZ including QCNW-1275TAZZ (VTR Adj. Jig cable)The first one mentioned has 8 switches and one push button (stop Adj.)labeled as follows: 1.) CAM/VTR Power switch 2.)Sensar Adj. 3.)MechanismAdj. 4.)Battery Adj. 5.)Error Indication 6.)Pass Mode 7.) CAH Adj. 8.)VTRAdj. Then there are 14 test pins labeled TP1-14 Hitachi DSP R Interface Board Jig MCM part #7099448 w/ DSP AV outputadapter MCM part #7099456. This jig also has three spring clip test probes(black, yellow, white). Has a 9-pin female serial type connector as well asa 25-pin connector. Sharp "Fixture" jig: w/ extension cable. RUNTK0309TAZZ . Not much toexplain other than a bunch of surface mount electronics including a remotecontrol sensor diode and three female RCA Plugs labeled: Video Out, MonitorOut, & Video In.Samsung interface board Ver. 2.0: Small silver rectangle box (4 1/2" X 21/2" X 1 1/4") One end has a 25 pin female parallel plug. The other end hasa DC 6V plug, a plastic 3 pin plug in that is labeled "ADJ", and a 15 pinfemale plug labeled "DDC"LG Monitor Adjustment adapter: (5" X 4 1/4" X 1 3/4") One end has two toggleswitches; one labeled in the upward position "V-SYNC" the other "ST". Nextto that is the red LED power indicator and then the wall plug in. The otherend has a 2 male pin plug in labeled "RS232C"...

There is always one or most cases on newsgroups MANY in the group that justfeel they have to comment on anything that pops up. Not that I should haveto explain myself since it really has no baring on someone either wantingor not wanting an item and just moving on and not having to comment but Iwill. I have had these for quite some time from an auction that was held ata repair facility that closed its doors; not form a "hamfest". I've never understood why there is always someone that has to jump atthe first opportunity to share their "knowledge" on something's "worth". Inever expected to get rich off of these or even make any $$ I was justtrying to see if anyone had a use for them being I do not. Thank you for stepping up and being the spokesperson for everyone onthis group we appreciate your knowledge and concern for keeping "worthless"items off this group. Good luck at your "hamfests" that you have ampleknowledge on.

Anyone NEED these test jigs?

Apr 03, 2007 21 Replies

Rate this thread:

Charles Schuler 19 years ago

Then WHAT was behind that "Up your meds" comment of yours?

Huh?

Vote

Charles Schuler 19 years ago

I can't deal with false quotes and delusional responses.

PLONK!

Vote

Join the Discussion

Have something to add? Share your thoughts — no account required.

Didn't find your answer?

Ask the community — no account required