The common point is sometimes used for fault detection.
When I was at Motorola SPD in the '60's I developed a circuit that could detect just about any fault, shorted or open diodes and shorted or open windings, by viewing that node. That node, BTW, is often labeled "S". Old GM alternators brought that out as a post on the back of the alternator (before regulators were internal... that's what some of my patents are all about... integrating the regulator).
That was before CAD ;-) If I can find my hand drawing, I'll post it. ...Jim Thompson
--
| James E.Thompson | mens |
| Analog Innovations | et |
| Analog/Mixed-Signal ASIC's and Discrete Systems | manus |
| San Tan Valley, AZ 85142 Skype: Contacts Only | |
| Voice:(480)460-2350 Fax: Available upon request | Brass Rat |
| E-mail Icon at http://www.analog-innovations.com | 1962 |
I love to cook with wine. Sometimes I even put it in the food.
The common in the Wye connection (called "Neutral Junction" in the photo on page 18) goes to the 4th pair of diodes (and typically the regulator). The other three pairs of winding ends ("Stator Lead Ends") go to the other three pairs of diodes.
Not the alternators I've taken apart. The star point is typically a crimp, and serves no other useful purpose.
The field, and regulator power, are normally taken from an additional set of diodes, usually 3, ie one per phase, such that the regulator is effectively isolated from the battery when the engine is not turning.
--
Mike Perkins
Video Solutions Ltd
www.videosolutions.ltd.uk
It's called an "IDIOT" light for a reason... as presently implemented it mostly tells you that the alternator is turning and has current in the field winding.
As I designed, the circuit compared the average value of "S" with 1/2 of the "A" terminal. Deviations were correlated with fault type.
Some GM versions enable the alternator regulator to function, so you can't remove it. (Saves GM the cost of a wire ;-) ...Jim Thompson
--
| James E.Thompson | mens |
| Analog Innovations | et |
| Analog/Mixed-Signal ASIC's and Discrete Systems | manus |
| San Tan Valley, AZ 85142 Skype: Contacts Only | |
| Voice:(480)460-2350 Fax: Available upon request | Brass Rat |
| E-mail Icon at http://www.analog-innovations.com | 1962 |
I love to cook with wine. Sometimes I even put it in the food.
Photo on p. 25. Note callouts for 6 diodes but you can see 8 round circles -- those are the diodes. Eight. (And yes, I've seen the rectifier and each of the 8 have leads soldered to each bus (or something...). I can confirm that firsthand.)
My conundrum remains:
By "common" are you referring to the (-) terminal? We agree that that terminal goes to chassis (presuming neg. ground chassis).
I'm talking about the common point among all 3 windings -- the center terminal of the "Y" configuration.
The + and - from the six diodes is connected to a series pair of diodes. The junction of that pair goes to the neutral junction of the stator coils and the regulator. Like this:
The 4th positive diode is a circle, just visible. The negative diodes are on the flip side of the rectifier so only the solder joints of the diode leads are visible as square tabs.
The 4 connections for the 4 winding terminals (3 windings + the common) are are around the periphery of the rectifier plate (only 2 called out, labeled "stator taps" in the original PDF reference).
That pictured alternator is one used on Hondas. ISTM it's a Nippon-Densi or such.
I have too much experience with same. I went through 3-4 boneyard ones before I bought a rebuilt one from Retarded Auto Parts. That brand/model alternator is nice because the diode array unscrews easily. No unsoldering needed.
That particular alternator has 4 pairs of power diodes; the center point of the wye has a pair from there as well.... and I have no idea why... Jim??
That said, all recent alternators also have a diode trio of tiny diodes. Their function is to rectify enough power to excite the rotor. It takes a few amps to drive it. Until it's up to speed, that excitation comes from the battery, through the red idiot light. When the alternator is up to speed, there is 12V on the battery side of the lamp, and 12v on the load side....and it goes out.
--
A host is a host from coast to coast.................wb8foz@nrk.com
& no one will talk to a host that's close........[v].(301) 56-LINUX
Unless the host (that isn't close).........................pob 1433
is busy, hung or dead....................................20915-1433
Those were alternators with only six power rectifiers, right?
The power rectifiers connected to the Wye common are used to extract
3rd harmonic power- yielding up to 10% additional current capacity- when operating at high speed.
Best regards, Spehro Pefhany
--
"it's the network..." "The Journey is the reward"
speff@interlog.com Info for manufacturers: http://www.trexon.com
Embedded software/hardware/analog Info for designers: http://www.speff.com
One problem with this arrangement... if the red idiot light burns out or a wiring fault opens the circuit, the alternator won't "bootstrap" the next time you start the car, and you won't (of course) get any red-light warning. Dead battery, here we come.
But THAT'S why I'm asking here: this Denso alternator (used in MANY Hondas, Toyotas, and myriad other makes) does have a common terminal connection to the rectifier. The rectifier has EIGHT diodes.
Yes I agree that common configuration is 6 diodes. That's why I'm confused. The system is quite populous and apparently functions. I just don't understand how.
That's why you LOOK at the Idiot Light when you turn the ignition switch on, just before you start the engine. A lit ALT bulb means it is present and functioning.
ElectronDepot website is not affiliated with any of the manufacturers or service providers discussed here.
All logos and trade names are the property of their respective owners.