Embedded Programming

How to protect data on CF (reverse engineering)

Take a look on this situation: My company made some new device with very new technology on it. We use for example some...

9 comments posted 21yrs

posted by HPmaster

9 comments posted 21yrs posted by HPmaster

One thing that I don't understand about CD hardware(One out of many)

Hi All, One thing that I don't understand, out of many. Is the chipset that drive the pickup mechanism(Loader) can work...

0 comments posted 21yrs

posted by roeido

0 comments posted 21yrs posted by roeido

PM3585 Maintenance - Who can help ?

Hi all, We own a good old PM3585 Philips/Fluke 200 Mhz state analyzer. It has been running fine for years and years now...

0 comments posted 21yrs

posted by abeaujean

0 comments posted 21yrs posted by abeaujean

Looking for low-side switch with crrent sensing

I need to make a heater circuit more intelligent. The existing design uses a low-side switch with with a simple logic f...

12 comments posted 21yrs

posted by rphenry

12 comments posted 21yrs posted by rphenry

MISRA Rule 45

Hi! I would like to define a pointer to a hardware register. I have done as follows: typedef unsigned int Hw_Register;...

17 comments posted 21yrs

posted by programmer_71

17 comments posted 21yrs posted by programmer_71

Co-simulation tools question

Hi: Has anyone had experience with Hardware/Software co-simulation tools ? About 6 years ago, I used Mentor Graphics Se...

0 comments posted 21yrs

posted by saz25

0 comments posted 21yrs posted by saz25

ATmega SPI question

Hi all, Supposing AVR is a configured as a Master SPI device. Is it possible to discard AVR master SCK output signal an...

13 comments posted 21yrs

posted by habib

13 comments posted 21yrs posted by habib

PC-104 plus help

Hi Firstly I am very new in this topic and my questions may seem weird o funny at first glance : I need a card, that ca...

0 comments posted 21yrs

posted by e116487

0 comments posted 21yrs posted by e116487

Wanted: Lauterbach ICE Renesas SH7055

Want to buy a full ICE for Renesas SH7055 if anyone has one. -nets email: st_enX@Xste_nl.com (remove undercore and upper...

0 comments posted 21yrs

posted by no

0 comments posted 21yrs posted by no

Difference of core registers and peripheral registers

Respected Experts, I am Ravi Kumar.N, working on intel processor. I am new to embedded system. I have a query regarding...

1 comments posted 21yrs

posted by ravikumar.n

1 comments posted 21yrs posted by ravikumar.n

large FIFO buffer

Hello all, I am in the middle of laying out a design for a medical device the reads in data pretty quickly (~20MHz) in...

8 comments posted 21yrs

posted by kumpf

8 comments posted 21yrs posted by kumpf

ATmega8535 and USART post-initialisation delay required?

Is there a requirement to delay using the USART (at least for asynchronous transmission) for a period of time after ini...

2 comments posted 21yrs

posted by ffffh.no.spam

2 comments posted 21yrs posted by ffffh.no.spam

20Amp H-Bridge driving with AVR

I'm an electonic amateur enthusiast and I want to drive 20Amp 12-24v DC motors with a H-bridge controlled with an AVR....

4 comments posted 21yrs

posted by <Huaci>

4 comments posted 21yrs posted by <Huaci>

Binaries compiled with ADS 1,2 not working..but the GNU versions are working fine!!

Hi, Im working on the AT91rm9200. I had compiled a few programs using the ADS 1.2 package. But ive found that all of a...

3 comments posted 21yrs

posted by prehistorictoad2k

3 comments posted 21yrs posted by prehistorictoad2k

Copying to RAM then executing

Hello folks, Though Ive been programming for years now, I am new to embedded programming. The problem that I have right...

5 comments posted 21yrs

posted by shafik

5 comments posted 21yrs posted by shafik