Embedded Programming

Initialize the Task Control Block

Hi there, I am wondering how to fill-up the TCB at the very first time when the intended task is yet to run. At that po...

3 comments posted 21yrs

posted by vibnwis

3 comments posted 21yrs posted by vibnwis

USB Host & PDA

Hi all, I have a PDA Ipaq 4150 and I want to connect to an external homemade device which has USB interface. It seems t...

5 comments posted 21yrs

posted by juklingos

5 comments posted 21yrs posted by juklingos

Controlling torque of single phase ac induction motor

i have a dayton shaded pole single phase ac induction motor with 1/150HP, 3000 RPM, 230 V, 60 Hz frequency and Full Loa...

3 comments posted 21yrs

posted by byju.ganga

3 comments posted 21yrs posted by byju.ganga

EDK Flashwriter Problem on Memec Board

Hallo at al I use a evaluation board from memec insight with additional adapte which have a flash. Now I try to write s...

0 comments posted 21yrs

posted by digitreaco

0 comments posted 21yrs posted by digitreaco

Difference between 24LC32 and 24LC32A using PIC 16F877A's I2C protocol?

Hello all, Are there any architectural differences between Microchips 24LC32A and 24LC32? I use a code which works fine...

4 comments posted 21yrs

posted by mansoor.naseer

4 comments posted 21yrs posted by mansoor.naseer

LXT972 and U-Boot

I am porting U-Boot from a PQ2FADS evaluation board to a custom board with an LXT972 Ethernet PHY. Anyone done this and...

0 comments posted 21yrs

posted by jobhunts02

0 comments posted 21yrs posted by jobhunts02

A couple basic questions regarding ARMs and DSPs

Hi - I just have a couple pretty simple questions regarding ARMs and DSPs. I should preface this by saying that I'm com...

4 comments posted 21yrs

posted by mnoone.uiuc.edu

4 comments posted 21yrs posted by mnoone.uiuc.edu

transfering binary file using hyperterminal

hi all, I want to transfer and receive a binary file using hyperterminal to the soft core processor through UART.Is it...

8 comments posted 21yrs

posted by kittyawake

8 comments posted 21yrs posted by kittyawake

How do I calculate this?

If an AMD processor with no special power-saving features is drawing 200 Watts while running at 2 GHz with a 200Mhz Fro...

19 comments posted 21yrs

posted by I.Hope.The. Pope

19 comments posted 21yrs posted by I.Hope.The. Pope

FIFO as a Logic Analyzer; Clock synthesizer

Hi! I have a big FIFO chip covered by dust, that I'd like to finally use. The most useful application I'm imagining for...

1 comments posted 21yrs

posted by nospam

1 comments posted 21yrs posted by nospam

Is anyone using the FSC ACE?

Hello from the Eighth Doctor Is anyone using the FSC ACE for new designs? I am planning one for the widget, and I need...

0 comments posted 21yrs

posted by drwho8__NOTME__

0 comments posted 21yrs posted by drwho8__NOTME__

Micro-VGA Adapter.

Released 20th April 2005 Micro-VGA Adapter. RS-232 DB-9 to VGA DB-15. The MicroVGA is a graphics adaptor that allows th...

0 comments posted 21yrs

posted by x456dy9p3

0 comments posted 21yrs posted by x456dy9p3

Programming BPM pin in intel CeleronULV

Sorry I don't know in which forum I should put this question. I want to program the BPM Breakpoint Monitor pin in Celer...

0 comments posted 21yrs

posted by soumit.mukherjee

0 comments posted 21yrs posted by soumit.mukherjee

SPI Serial EEPROM design

Hello: I'm starting up a new desing using 4 Atmel AT25HP512 devices connected to a 4 wire SPI interface. My question is...

12 comments posted 21yrs

posted by george.martin

12 comments posted 21yrs posted by george.martin

ATA FPGA IP Core

We would like to interface a DSP, TMS320C67xx, to an ATA-5 harddisk directly. Is it possible? Does anybody sell FPGA IP...

0 comments posted 21yrs

posted by digitalsignal999

0 comments posted 21yrs posted by digitalsignal999